59650003100 Kenmore Refrigerator - Instructions

I removed the 5/16 inch hex head nuts holding the rear access panel where the power cord was connected. Once removed, I released the Molex plug and ground wire. I connected the new cord, screwed in the ground and installed the rear panel. Having the exact OEM part made the job quick and easy.

Snapped into place with the attached clips. Could not be easier. Really great service from PartSelect--got here faster than I expected. This was a great service--would recommend to everyone!

We unplugged the refrigerator, used a knife to pry out the old switch. Cut the extra prong off of the new switch and connected the switch to the wire connectors. Slid the switch back into place plugged the refrigerator back into the outlet and . . . . . . Wah, lah, the light and switch worked again. We washed and then simply slid the vegetable crisper into the holder and replaced the one that had broken. This was a really great experience and it was quick and easy to fix on our own.!

I did a few tests with the old ice maker and determined that it was the ice maker itself that was faulty. The replacement part I ordered exceeded my expectations in the time it took to get the part. I reused the arm, wire harness and clamps from the old icemaker. Then it was a simple install into the bottom freezer compartment, turning on the water supply and bingo...lots of ice cubes.

Firts checked the parts received werer correct for the repair and the correct part numbers ordered. Then removed the ice bucket with the auger in bottom. Emptied ice from original bucket auger assembly. Checked out the removeal of the face cover for the bucket auger and removed it from clips that held it in place. Checked the specifications of the old ice bucket compaired to the new parts. Installed the aurger assembly into the new ice bucket and removed the two screws from the old unit to use in secure the auger assembly in the new bucket. The only tool needed was a 1/4 inch nut driver. Installed the face place on the new ice bucket auger assembly and tested the fit in the freezer. Ran test of the auger assembly without ice to ck for any misinstlled parts. Refilled the ice bucket with ice and tested with ice to complete the repair.

Replaced filter and the water started to flow like the Nile River and the ice maker came back to life.

Removed screw under ice maker. Tilted ice maker up to remove unit from upper two screws. Disconnected plug at rear of freezer. Attached wiring harness, baler arm and cover from old to new ice maker. Reinstalled in reverse order. Had ice within one hour. Very easy fix.

disconnected wire connections, pulled old overload relay and running capacitor out like a plug and plug in the new one then reconnected the wires.

One day when i went to get ice our ice maker started to jam. When i took it out i noticed that the metal arm that turns was out of position and blocked due to the End cap being out of place. I then put it back in place and it happened again. The bucket cracked due to the pressure caused by the ice been . The only problem that i have now is that when i hit cubed ice, crushed ice comes out...and when i hit crushed ice, cubed ice comes out. The installation and swapping of parts wasw really easy. Partselect has great breakdown diagrams so if you get lost u can turn to them.

Unscrew filter. Screw on filter bypass

Replaced refrigerator cooling control. No luck. Replaced freezer cooling control. No luck. Coils were icing up. Unplugged frig and allowed coils to defrost. After more poking around, found that condenser fan was not spinning. Touch it and it'd start. That was definitely in need of replacement. Replacement was easy. Refrigerator is now running as it should.

I didn't. Don't know how to get to light bulb to change it for this specific model

Popped out with butter knife and unplugged 3 prong connector and reversed with anew switch.

But, unfortunately it got broken again exactly same way as before.
So, I ordered same switch again for 2nd time.

Maytag should recall that Rocker Switch and build with better materials.

Took ice tray out, removed plastic decorative cover, remove the four nuts under the cover, slide out the ice auger assembly as one piece. do not take auger assembly apart. I repaired mine once, difficult without a schematic picture, many parts, replaced everything back into the new ice bucket. Easy job!

The Ice maker unit had to be removed and the shaft had to also be removed, which required dis-assembling the motor drive. The thickness of the shaft and the bearing fill cup prevents it from simply pushing it in place. Other than that I have Ice.