25354363401 Kenmore Refrigerator - Instructions

The parts supplied were made to fit. The hardest part was getting the original broken tabs out of the internal walls of the fridge with out damaging the internal insulation. I punched the center locking pin through completely, dug out the broken tabs and then reached into the hole with a dental pick and pulled out the center pin. The new parts fit perfectly and with a plastic mallet, tapped the new locking pin into place.

It wasn't clear how to disassemble the Ice / Water dispensing unit to get at the lever for replacement BUT the website had a great exploded parts view of the door and assembly so I was able to print that and from the diagrams you can easily work out how to pull it apart..
A bit fiddly and you need to power down the Fridge as there's 120v behind this panel (tip : dont drag out a heavy fridge, flip the breaker at the main panel to isolate the power) .

All fixed for $50 , compared to having to call out some guy who'd charge me $100 plus parts !! great deal !
Thanks !

Turn of power at the circuit breaker.
Remove the water tray by pulling straight towards you.
Remove the three screws at the bottom of the control panel.
Have someone hold the control panel while you remove the six small screws that retain the circuit board.
Gently ease the circuit panel away from the plastic frame and disconnect the six wire connector on the left hand end, followed by the two light connectors with black & red wires, then remove the four wires with spade connectors from the microswitches - noting where each goes. The control panel & circuit board can then be set aside.
Remove the three screws that retain the interior plastic frame. The plastic frame can then be eased forward taking care not to pull out the water pipe. This allows access to the screws that hold the actuators, which should both be removed. Unhook the spring & remove the broken actuator. Feed the new actuator wire up from the bottom of the frame and insert the left hand pivot first and twist gently to snap the right hand pivot into its recess. Replace the retaining plates & screws. Don't forget to the hook the actuator spring into its clip. Test the operation and ease the plastic frame back into position and attach with the screws.
Re-connect and reassemble the circuit board and front panel in the reverse order.
Power on and enjoy a glass of fresh cold water! You may need to press the reset button on the front panel to reset the lights in the actuators.

Took the ice storage bin out. Took the unit apart,and disamble the augar unit. Ordered parts from manufacture, which arrived in two days. As soon as I got the parts, I reassambled it. Work perfect. Good job!

First I removed one screw holding top hinge trim in place. I than removed two screws holding top hinge from refrig. I removed refrig door and laid it on a table. I than removed two screws holding the door stop and bearing hinge. I replaced the defective parts and reassembled in reverse order. Simple 10 minute repair.

We followed the video instructions and it went fairly smooth. After turning off the water at the street we found that the faucet at the wall had it's own "on/off" valve. When finished, we turned on the power and heard the gears going through their revolutions, but no ice was made. We waited 24 hours and still no ice. I removed the cover on the ice maker and adjusted the amount of water to see if that was malfunctioning. Still no ice was created. Waited another 24 hours - nothing. Waited another 24 hours (the site said that sometimes the ice maker would take time to reset itself) - nothing. Then on the fourth day after changing out the triple water valve we heard water being dispensed and later that day it put out the first ice in weeks. Another hour later another batch of ice cubes were ready and deposited into the bin. Since that time, we have had a full bin. I moved the set screw back to it's original setting because a little too much water was being delivered. The cubes weren't separating to individual cubes. That cleared up the problem. This was easily completed - we recommend others do their own work. Just be patient for the system to reset itself.

First removed food from the refrigerator door.

Second removed plastic cover plate and metal plate assembly from top of door.

Third lifted door of metal pin on bottom.

Fourth removed broken closer plate and replaced
with new closer plate.

Set door back in place.

Re secured the metal plate and plastic cover plate.

Replaced the door shelves and food. DONE.

I had removed the housing that the drum was in and taken the screws out to get to the broken drum. I removed it there was a set of 6 blades that crushed the ice that had to go back on the same order when I removed these I put them on a piece of wire in the order they came off (so I would get them back I the correct order). Then I reversed the order and reassembled it in the opposite direction . It was fairly easy to do. I'm a 68 year old disabled woman so if I could do it I'm sure you could to. Good luck. It cost me $14.00 if I had bought the whole assembly it would have been $150.00. So it was well worth my time and effort.

I followed the video tutorial published here. The step I altered was setting the shrink wrap; I did not have a heat gun to safely shrink it, so I folded it tightly onto itself and wrapped it in electrical tape. No more frost buildup.

Could have done it with my eyes closed! Removed shelf and drawer, then removed broken support rail. Removed screw from broken rail and put the new, two piece rail together using that screw. Snapped rail back onto wall...returned shelf to fridge...returned drawer to fridge...returned myself to sanity! Yee Haw Easier than installing it was ORDERING IT. I was amazed by the ease of that process. Your ordering site is incredibly easy. By the way...I am a blonde and for blondes everywhere...Look at what I could do :)

Unscrew 4 screws . Remove broken basket hangers. Install new basketo hangers. Screw in 4 retaining screws...

Twisted replacement bulb into place easily. Let there be light!

Noticed the evap fan wasn't working, so trying to disconnect the wire broke the connection so had to order a new motor. Installed the motor but it still didn't work. Had a technician look at it and he said it was the control board. Ordered and installed control board and still didn't work. The only element left is the evap thermostat. Jumped the thermostat and it worked so ordered and installed a thermostat. It works now

very easy to do. just snap into place

Removed the plastic water tubes cover with a nut driver. Disconnected water hoses. Dropped control box assembly with nut driver. Removed old filter base with phillips screwdriver. Assembly opposite.