59652673200 Kenmore Refrigerator - Instructions

Replaced filter and the water started to flow like the Nile River and the ice maker came back to life.

Firts checked the parts received werer correct for the repair and the correct part numbers ordered. Then removed the ice bucket with the auger in bottom. Emptied ice from original bucket auger assembly. Checked out the removeal of the face cover for the bucket auger and removed it from clips that held it in place. Checked the specifications of the old ice bucket compaired to the new parts. Installed the aurger assembly into the new ice bucket and removed the two screws from the old unit to use in secure the auger assembly in the new bucket. The only tool needed was a 1/4 inch nut driver. Installed the face place on the new ice bucket auger assembly and tested the fit in the freezer. Ran test of the auger assembly without ice to ck for any misinstlled parts. Refilled the ice bucket with ice and tested with ice to complete the repair.

disconnected wire connections, pulled old overload relay and running capacitor out like a plug and plug in the new one then reconnected the wires.

I pulled off the plastic shield from the front of the ice bucket. This exposed the two screws that I needed to remove to disassemble the ice crusher mechanism. Once the screws were removed, I was able to remove the helix and replace the end cap that was broken and place it in the new ice bucket. If I would have known it was this easy, I would have changed this out a year ago, instead of doing without crushed ice through the door for so long. Thanks PartSelect. com! I am a customer for life!

Snapped into place with the attached clips. Could not be easier. Really great service from PartSelect--got here faster than I expected. This was a great service--would recommend to everyone!

We unplugged the refrigerator, used a knife to pry out the old switch. Cut the extra prong off of the new switch and connected the switch to the wire connectors. Slid the switch back into place plugged the refrigerator back into the outlet and . . . . . . Wah, lah, the light and switch worked again. We washed and then simply slid the vegetable crisper into the holder and replaced the one that had broken. This was a really great experience and it was quick and easy to fix on our own.!

First, I removed the bucket and drained all the ice from it. Then I took the ice bucket out and lifted off the cover of it which exposed the teeth that grind up the ice. I then removed these in succession and placed on my table so I could make sure I put back together appropriately. Once I had the bucket with everything off of it, I replaced and threaded the auger back through it so I could attach the end cap to it. Once that was in place, I put the parts back on the way I took them off. It really was a painless process and saved a ton of money versus calling a repair person. Definitely will use the service again. Very prompt delivery as had the parts 2-3 days after ordered. Well done.

Freezer kept freezing over so the fridge wouldn't get cold air. Easy fix. Pulled all the shelves out first. Then took out the screws on the back wall of freezer. Removed the bottom panel only to expose the thermostat. Cut the wires and spliced them together to the color coded wires on the new one I purchased. My 4 year old could have done this. They supplied the wire nuts too!! Clipped it back on tied all the wires back together with zip tie and put the covers, screws and shelves back in. Works perfect. Was quoted $200 to do this job. Wish they were all this easy. Thanks PartSelect!!

Removed screw under ice maker. Tilted ice maker up to remove unit from upper two screws. Disconnected plug at rear of freezer. Attached wiring harness, baler arm and cover from old to new ice maker. Reinstalled in reverse order. Had ice within one hour. Very easy fix.

I unhooked the wire harness from the ref. and took out three screws and pulled the old unit out. I than changed a few parts from the old icemaker to the new and reattached the new ice maker to the ref. and plugged the wire back in. everything is working fine. No problems. Also I was very happy with the ordering process. Thank you!!

I didn't. Don't know how to get to light bulb to change it for this specific model

I removed the 5/16 inch hex head nuts holding the rear access panel where the power cord was connected. Once removed, I released the Molex plug and ground wire. I connected the new cord, screwed in the ground and installed the rear panel. Having the exact OEM part made the job quick and easy.

One day when i went to get ice our ice maker started to jam. When i took it out i noticed that the metal arm that turns was out of position and blocked due to the End cap being out of place. I then put it back in place and it happened again. The bucket cracked due to the pressure caused by the ice been . The only problem that i have now is that when i hit cubed ice, crushed ice comes out...and when i hit crushed ice, cubed ice comes out. The installation and swapping of parts wasw really easy. Partselect has great breakdown diagrams so if you get lost u can turn to them.

Unscrew filter. Screw on filter bypass

Popped out with butter knife and unplugged 3 prong connector and reversed with anew switch.

But, unfortunately it got broken again exactly same way as before.
So, I ordered same switch again for 2nd time.

Maytag should recall that Rocker Switch and build with better materials.