61004753 Kenmore Refrigerator - Instructions

Replaced the old part with the new one and we're back in business again plenty of ice.

Turned of power and water to unit. Removed water lines and electrical wires to old valves, tagged wires and hoses before removing. Cut old hose and installed new hose kit. Change from two water lines to one. Remove old valves and replace with new, reinstall water and electrical wires.Turn on water to check for leaks if there are no leaks turn power back on and check for water going to ice maker. A really easy repair.

Removed screws, removed parts, spring popped off, didn't know where it was actually at, had a difficult time getting the spring in the right place, (the directions were not that clear), put back together 6 times before I got it right.

Followed included instructions. Thank you.

I just followed the directions that came with the part and it was very simple. Saved at least $100 on the repair. Anyone could do this repair. Don't call Maytag.

The repair was really simple - I followed the directions provided. I removed the screws holding the cover in place - unplugged the wiring harness - removed the solenoid and replaced with the new solenoid and door amd reassembled the parts. I wasn't sure if the solenoid was bad since the door was actually broken. I was able to test just using the new door - then replace the solenoid. It was all done in less than 30 minutes. Directions provided were GREAT.

First removed the grill from the fountain. Then removed the 2 screws, raised the escutcheon up and off the fountain assembly. Disconnected the power connection to the escutcheon and laid it aside. Removed the 3 screws holding the fountain assembly and disconnected the power supply from it. Removed the broken door pieces. Removed the 2 screws from the solenoid and replaced with new one and replaced the screws. The instructions said to rotate the spring counter clockwise 1/2 turn but I had to rotate it a full turn (to make the door tight when it closed) and insert the end of the spring in the opening of the fountain bracket. Insert the solenoid plunger into the recess of the door strike (the diagram in the instructions helped because this was the part that was broken and I could not figure out where it went). Then I installed everything back the way I had taken it apart.
I am a 61 year old woman and pretty good at taking things apart and putting it back together. My husband usually lets me fix things because I have more patience than him.
I would like to thank parts select for their packaging of the parts and the included diagram.

This is an easy repair and doesn't take hardly any time, once you can identify the electrical bridals to disconnect and the position of the new ice chute door interface point with the solenoid.

The supplied directions are complete but were quite a bit blurry. The more general dissasembly which is effectively 5 screws and two electrical bridals to remove/disconnect is straight forward. Pay particular attention to the mounting point of the ice door interface with the solenoid. I did it twice because I didn't align the door properly the first time:-)

Much too easy a job than to "call the guy."

directions in package really made it easy. Saved $175.00

repaired by following the video instructions. the video is a great how to do it yourself tool !!!!

Easy to follow directions. Got to the part where the old solenoid would be removed and found that one of the two wires the connected to the old solennoid had become disconnected. Reconnected and everything works. Will keep the kit now as backup and instructions in case I need to repair again. Very satisified.

I removed the outer cover from the door, removed the broken parts, and cleaned the area of debris. After cutting off the power, I replaced the solenoid and door, then prepalce the outer cover. The parts were delivered promptly, and the job when very well.

Pulled out ref. removed 3 screws holding the fiber covering. Removed one screw holding the water inlet, disconected the elecrical and the water line from supply and the tubing going to the water filter.
Then connected water lines and the electrical to new inlet, and attached the new inlet back with the one screw, reattached the fiber backing. All Done.

Note: ice cube tray did not fill immediately...air in water line??? However, after short time all works fine.

Couldn't believe how easy this was. The pictures you provided were perfect everything went exactly as the instructions said. I had to of saved at least $150.00. I would grade my mechanical skills at about a C+ at best and this was an easy fix.
If I need appliance parts, I now know where to go.

First I removed the 5 torx head screws that held on the outside panel. Then I unplugged the 2 electrical connectors to the circuit boards, one goes to the touch pad the other is the power. Then I removed the assembly. I only needed the part that holds on the round door but I replaced all the parts that came in the kit.
With the directions that they sent me with the parts, and since I was the one that took it apart. I was able to fix it in about 20minutes and it worked great.