61004753 Kenmore Refrigerator - Instructions

Our Refirgerator had custome wood covering to match the cabinets. Be sure to take the covering off first. There are four screws on the left edge fram that need to be removed and two on top of the tpe edge frame. The panels then slide right off. Remove the spill tray and unscew the two screws at the bottom. Slide up the key pad and there are three screws behind the key pad that have to come out. There are two "plug in connections that have to be disconnected to lift the dispenser unit out. Take care not to damage or separate the connector wire from the keypad and the circuitboard.

The new solenoid and flapper assembly is different than the original. My guess is the orginal design was part of the problem and the redesign allows the solenoid to work better. I was suprised the new assembly did not come with a tension spring... SO be careful and DO NOT loose the tension spring from the old assembly. there are two screws that hold the olde solenoid in plae wonce you remove the flapper and tension spring. Put the new solenoid in, hold the tapper out and put the flapper assembly in. Rotate the flapper rod until you can seat the solenoid tapper. Replace the tension Spring and then reassemble as in reverse order.

the repair was simple and I not inclined to do these things at all. I turned off the water supply line, unplugged the unit, unscrewed the outlet valve, removed the lines and inserted the new one. piece of cake

Repair was a breeze, just like in the provided directions. Removed the trim and wood panels, accessed the door, removed the panel, replaced the solenoid and put it all back together-piece of cake! Unfortunately, about 45 minutes after putting everything back together, water started shooting out of the dispenser and would not shut off. All of the controls became non-functional. I opened the freezer door and that made it quit shooting water. Had to remove the dispenser panel again and unplug the power to it. Have not had a chance to trouble shoot further. Did note the new solenoid seemed very warm to the touch. Did it possibly short something out?

I reviewed the instructions which were very clear and began. I removed the catch tray to access the two screws. I removed those and lifted the front off. I then removed the three screws holding the dispenser unit and gently pulled the unit out. I then disconnected the two electric connnections and removed the dispenser unit from the refrigerator. The ice door tab was broken, so I really just needed to replace the door, but since I received the other new parts in the kit, I went ahead and replaced those as well. The directions were very specific, just make sure that the spring is inserted correctly. I then reinstalled the unit. When I finished, I tried it but the door would not shut properly. I disassembled the unit again and found that the spring had come loose. Looking back , I probably knocked it loose when I was installing the water tube back into place. I reassembled, making sure that the spring was installed correctly, and everything worked fine.

Pulled out frig and unplugged it from wall. Took out 2 screws to gain access to valves. Took out screw holding bracket holding valve bracket to frig and removed one more to remove the old valve from bracket. Simple water disconnect with wrench after that and changing the lines to door cutting them back 1/2 ", direct plug in electrical connections, replacement exact like original. I had previously changed the other solinoid with the problematic Y connector but that didn't do the trick. This fix seems to be the correct one to fix the problem.

Exchange both water valves with new (took me 5 min.)- same brand as original. Nothing else works better. Dont wast your money for Amazon parts or after market.

Removed 3 torx screws, used pliers to release control board clips and removed board. Unplugged old board and plugged in new board. Replaced cover and lights were back on.
Put cup under water dispenser and pushed for water. The control board immediately exploded and smoke came out. The board was burnt to a crisp just like the one I replaced.
Now I'm out over $200 bucks.

Followed included instructions. Thank you.

Replaced the old part with the new one and we're back in business again plenty of ice.

I removed the two screws from the front door panel, unhooked the wire, removed three more screws and removed the broken door. I replaced the door and replaced everything in reversed order. I did not need to replace the solenoid so I still have that if needed in the future, The instructions were so easy, it took less than 5 minutes and I estimate saving about $90.00 on a sevice call after deducting the cost of the part from PartSelect.
I will check out PartSelect for future repair jobs.

Thanks

Turned of power and water to unit. Removed water lines and electrical wires to old valves, tagged wires and hoses before removing. Cut old hose and installed new hose kit. Change from two water lines to one. Remove old valves and replace with new, reinstall water and electrical wires.Turn on water to check for leaks if there are no leaks turn power back on and check for water going to ice maker. A really easy repair.

Removed 4 screws and disconnect the circuit board, replaced the broken door and reassembled the unit. Solenoid did not need to be replaced, only the ice door. About 15 minutes and about 90$ saved in labor.

The video was fantastic provided by Part Select. Only difference I found was the use of shark bite connections, instead of screw on nuts for the top two hoses. Shark bites have to be pressed and removal can be done, would be a good idea for the video.

easy, step-by-step repair. replaced all parts that came with kit; no hastle. only issue was that "torx" head screwdriver was needed (which I had).

Shut off water and electric to refrig. Removed back panel. Removed water line. Removed valve, Disconnected other water line and electrical connections. Installed new valve in the reverse order.