1069600516 Kenmore Refrigerator - Instructions

It's self-explanatory. The procedure is obvious; it's just a little difficult. The only hard part is attaching the mounting brackets to the fan. If you can't tighten the mounting bolts, loosen them and reposition the brackets. You might end up mispositioning them at first, because they are hard to reach.

Followed the video instructions.

I followed the directions that came with the new part. Thank you for making it so easy. You sent me everything I needed to make the repair.

In my case the defrost thermostat was not the problem. Not worth going through the hassle of checking the thermostat as I would have had to cut it out and test it in another freezer (while the food that was in the freezer was being stored elsewhere). I just ended up buying it and replacing it. So, like I said the defrost thermostat was NOT the issue. I ended up getting a drain tube heater strap, and have been keeping my eye on the fridge. It hasn't been long enough to say the strap fixed the problem, but all indications are pointing to that being the case.

removed shims on screws holding motor together, enlarged hole in mounting bracket so motor screws could also go through mounting brackets.

My fridge did not have icemaker add on. The evap fan is in the freezer behind the back panel. Empty the freezer section (into a cooler) and turn the fridge off. Remove all the shelves in freezer section. Remove the shelf support tabs by lifting them up. use phillips head screwdiver to remove back panel in freezer section. Use nut driver to remove fan shroud. Remove old fan and save the mounting arms. Install mounting arms on new fan and install fan. Install shroud, back panel, shelf mounts and shelves. Thats it!

Went online with the model number, the part was very easy to find, diagrams helped me to have confidence in the choice. Parts came in two days, tore them open and used a screw driver to replace the broken shelf brackets, replaced shelves, I am a happy camper!!

Just moved into a new rental home and a few days in the bar that holds all the stuff -- milk containers, juice jugs, etc. -- in the refridge door falls off. The old tenants had "fixed" it with tape on one side and paint stirrers and caulk on the other side. (No kidding -- a real overkill job they did).

I looked up the model number online and found this site and promptly ordered the parts for $6 plus shipping. The parts came and snapped right in perfectly. Took only a minute.

I really only had to use pliers to pull out the oodles of hard swirly caulk from the slots in the door left from the overkill job by the previous tenants.

PartsSelect is awesome! The site makes it easy to look for the part you want and the parts were perfect -- No more stuff falling out the fridge door.

PS. This form made me select the age of the appliance. I really have no idea since I just moved in and it was already here.

Ordered the wrong shelf, returned it and ordered the correct shelf. Placed it on the frame. Service was two days.

Slid the end caps onto the shelf, placed the tape on the pieces as noted in the directions, and put the shelf back in place. Fast service, exact part, easy to find on the web site! Great!

I hand screwed the fill tube into the water tube and stuck it into the freezer hole. I screwed the fill tube to the back of the refrigerator.

Thanks so much! You saved me a bundle!!

****Make are you order Capacitor & Starter relay too (we ordered separtely so had to pay shipping twice)**** Super easy just open access panel on back near compressor and remove retention clip with fingers, remove & replace both capacitor & starter, put clip and access panel back on, plug in and allow 8 hours to cool! Works like new again! Hope it goes another 10 years

After the front panel was removed, disconnected the timer and installed new in reverse order. The provided instructions could be more straight forward, I spent more time reading it than the installation itself.

I got the product very quickly. (thank you) Looked at online instructions that were quite vague. Pulled plug.Removed the holder for the fan motor slid it out to see what I had. Removed the mounting screws (3) and slid the motor an fan blade out. I made a cut between the wires and marked the "top" wire to motor to be sure to spin in right direction. Removing fan blade hold down clamp was NOT explained at all but I noted that the shaft on the motor was threaded, so I used pliars and held the shaft white un-screwing clamp. I cleaned the fan blades with degreaser and scraped edges of opening on holder opening. Make sure to use ALL the NEW parts included with this kit when re-installing. They send them for a reason. When slpicing and connecting wires it is a 50/50 shot if you don't mark before cutting. You can connect and try plugging fridge back for moment and make sure it is blowing OUT. Put everything back together and after turning DOWN the thermostats twice, fridge is back to usual. Ice maker is cranking out ice and outside case is cool to the touch.

Note: This can be a DIRTY job especially with 4 dogs in house. Fir and grease don't mix well

The repair was easy, I removed the cover on the top front of the fresh food compartment. It housed the defrost timer which was easy to identify and replace. Just removed a screw, unplugged the wires and replaced with the new part. Unfortunately, that wasn't the only problem. I also had to replace the defrost element that the timer sent power to. While I was at it, I replaced the defroster thermostat. The entire repair took under an hour, diagnosing the problem took the most time and effort.