25331620100 Kenmore Refrigerator - Instructions
Jump to:
Keep searches simple. Use keywords, e.g. "leaking", "pump", "broken" or "fit".
- Customer:
- Alicia from Torrance, CA
- Parts Used:
- 240311502
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
My end cap broke as a result of too many things piled in the door rack.
I snapped out the broken piece of the old Door Shelf Retainer Bar End Cap, snapped in the new one and reinstalled the door rack in my refrigerator.
Was this instruction helpful to you?
Thank you for voting!
missing bottom door shelf bracket
Received 3 parts. Snapped them together. Attached them to fridge door.
Was this instruction helpful to you?
Thank you for voting!
End caps were broken/missing on refrigerator
I installed new end caps brackets with bars by putting them in place. Now the refrigerator looks new again. These parts were installed in the door, which was broken/missing. This prevented a person from being able to store anything in the refrigerstor door until it was fixed.
Was this instruction helpful to you?
Thank you for voting!
Refrigerator Door Shelf Bars were broken
These were easy pop in pieces so no tools were needed. Very easy and quick. What I liked best about PartSelect.com was the pictures and labeling used in order to select the correct part. That was my biggest concern. It only took me about 15 minutes to find and buy the parts I needed.
Was this instruction helpful to you?
Thank you for voting!
Door shelf retainer end caps were broken.
Ordered whole new retainer assembly. New bar was incorrect part, but endcaps were OK, so got old part out of the garbage and straightened damaged areas, used new endcaps, and reinstqalled on door. Works.
Was this instruction helpful to you?
Thank you for voting!
Our refrigerator and freezer door shelves were falling apart when we opened either part.
We cleaned all the parts we had and did a quick survey of which pieces needed to be replaced. We ordered the parts and they arrived within 48 hours. I snapped the pieces together and put all the shelving back together. I do have one difficult spot where the tab inside the door that the shelving attaches too was also ripped. I filled the spot with super glue and let it set for a day and finished installing the last shelf in a few seconds. The Best News...No more ketchup or juice bottles falling to the floor everytime you open the door!!
Was this instruction helpful to you?
Thank you for voting!
Broken Shelves
All three shelved had been broken for years. I finally broke down and bought the parts, and I can't believe I waited so long. The retainers are very easy to install. The bars take some time to measure, and cut, but once that is done, it is very easy to assemble the parts, and get back to having usable shelves.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Curtis from Winlock, WA
- Parts Used:
- 5304464438
- Difficulty Level:
- Really Easy
- Total Repair Time:
- 15 - 30 mins
won't start repaced the run capacitor didn't solve the problem so I ordered a defrost timer
I watched the videos (they really help) and followed the steps. Everything went smooth with no surprises
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- francis from arlington, WA
- Parts Used:
- 241537103
- Difficulty Level:
- Really Easy
- Total Repair Time:
- 15 - 30 mins
- Tools:
- Nutdriver
has lights,no fan or compressor
jump thermostat,fan and compressor came on, ordered thermo from this excllent parts supplier, part came in 4 days later, it was exact replacement, works exactly right!
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Charles from Wallingford, CT
- Parts Used:
- 5303918549
- Difficulty Level:
- Really Easy
- Total Repair Time:
- 15 - 30 mins
- Tools:
- Nutdriver, Screw drivers
Not getting cold in lower Refrigerator
Watch the video provided by PartSelect and did exactly the same percedure. Shows what screws to remove and how to remove and replace the part. The freezer compartment was iced up quite a bit so defrosted it before installing part.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Gary from Hudson, FL
- Parts Used:
- 5304464438
- Difficulty Level:
- Really Easy
- Total Repair Time:
- 15 - 30 mins
- Tools:
- Screw drivers
not cold enough
per the video..easy installation....unfortunately the temperature did not improve. We still have a refrigerator temp in the upper freezer.....and a "cooler" in the refrigerator section
Was this instruction helpful to you?
Thank you for voting!
Door shelf retainer bar was about 1" too long.
I needed to cut the bar to fit or return it for the bar that was almost three times the price. The notches to hold the end cap are no longer on that side so I also needed to clamp the metal bar to the end cap.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Judith from Spring Hill, FL
- Parts Used:
- 5303918202
- Difficulty Level:
- Really Easy
- Total Repair Time:
- 15 - 30 mins
- Tools:
- Nutdriver, Screw drivers
Evap coil was solid ice, fridge was 64 degrees.
Exactly as the video showed, except I had to take the evap coil cover off and use a hair dryer to thaw it out. It was still frosting up too much, so I ordered the thermostat as well. Both were really easy, once i saw the location of the defrost timer and the thermostat. Thanks for the great site, prices that put the big store to shame, and the good video too!
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Peter F from Farmingville, NY
- Parts Used:
- 5303918549
- Difficulty Level:
- Really Easy
- Total Repair Time:
- 15 - 30 mins
- Tools:
- Nutdriver
Refrigerator And Freezer Not Cooling Sufficiently
Refrigerator and freezer was not cooling sufficiently due to an inoperative evaporator cooling fan. Replacing the mini evaporator fan was extremely easy. Here are the steps needed to replace the fan. Step 1: Unplug refrigerator/freezer main power cord from the electric wall outlet. Step 2: Remove the food rack from the freezer compartment. Step 3: Using a 1/4" nut driver, remove the (2) 1/4" screws that hold the freezer vent panel/temperature control in place. Step 4: After removing the screws, disconnect the motor's wire harness connector which is located on the top left corner behind the freezer's vent panel/temperature control. Step 5: Pull away the entire vent panel/temperature control panel and lay it flat on a table. Step 6: Remove the vent cover from the main panel by holding the left side and the right side of the vent cover and squeeze both ends at the same time. Step 7: With the motor now being visible pull the motor's fan blade straight off. Step 8: Using the 1/4" nut driver, remove the (2) screws that hold the motor bracket to the rear of the main panel. Step 9: Using the 1/4" nut driver remove the (2) screws that hold the motor to the bracket and the (1) ground wire screw. Step 10: Install new motor back onto the bracket with the original (2) screws and the (1) ground wire screw onto the same locations.Step 11: Re install the (2) screws that mount the fan bracket to the back of the main vent panel.Step 12: Push the motor's original fan blade back on the shaft until it's fully seated. Step 12: Snap back in place the small vent panel back onto the main panel. Step 13: Push in place until you hear a click, the motor's wiring harness connector back onto the top left corner of the freezer's main power wire harness connector. Step 13: Push the main vent panel until it's in place and then reinstall with the original (2) 1/4" screws. Step 14: Reinstall the freezer's food rack back in place. Step 15: Plug in the main power cord into the wall outlet. Get ready to enjoy ice cold drinking water and a super cold freezer. Pete,your weekend mechanic
Was this instruction helpful to you?
Thank you for voting!