1069650482 Kenmore Refrigerator - Instructions

taped the door shut ,measured a block of wood and stuck it under the door for support.....unbolted bottom hinge,slipped on hinge bracket and reassembled.no muss no fuss.

unplugged relay and plugged in

Forty years ago I serviced air conditioners and all kinds of refrigeration. At that time starting relays were electro mechanical, I hadn’t looked under a refrigerator in a lot of years and was surprised to find out that the new relays were solid state. The defective one had a bunch of broken pieces floating around in the case. I jury rigged a starting cord and confirmed that the compressor would start and looked at running current for thirty or so seconds. I ordered a new relay kit and it worked just right. I’m seventy five years old and it takes me longer to get up off the floor than it took to replace the parts. Your delivery was first rate the parts got here before I finished doing the paint touch-up on the door under the ice maker/water dispenser. Fed ex was easily three to five days faster than the brown truck.

Everything worked perfectly---thanks to the suggestion of your call center agent. She suggested that since the replacement door handles were no longer available, I should consider repainting them--it worked like a charm. Please tell her she was a life saver. We rent that house in Fl and my returning tenants had complained about the discoloring refer handles. Thank you

We had a refrigerator that had no ice maker at all, but it had the wiring behind the freezer panel and the wiring for the solenoid valve at the bottom of the refrigerator. The installation went easy for me, but I do not think the average homeowner could handle it. There are always little variations from model to model so some of the diagrams were not quite the same as my unit. But all the necessary parts and hardware were there and the install went fine. its crabnking out perfect ice like crazy.

Rather than pay a repairman an assessment fee, then the cost of the repair to the existing icemaker, I decided to replace the icemaker for a lot less. The Add On Icemaker kit came with installation instructions. The kit included the ice maker, as well as the hose and water feed control on the back. Originally, I was nervous about attempting to replace the icemaker. I watched a video on YouTube about replacing an icemaker and saw how easy it could be. Following the enclosed directions, and Wow!, it was extremely easy to remove and add the new icemaker. Don't pay to have someone else do it! This is a no-brainer.

Insalled fan motor,problem went away. Thanks

1. Unplug the refrigerator. 2. Remove the back cover at the bottom of the refrigerator. 3. Remove the two screws holding the vertical black bracket the fan is mounted to. This allows the bracket to move easily. The bracket does not have to be removed. 4. Removed the four screws holding the fan bracket to the vertical bracket. 5. Unplug the power connector from the fan motor. 6. Remove the entire fan bracket assembly from the refrigerator. 7. Remove the 4 screws holding the fan motor to the fan motor bracket and unmount the fan motor. 8. Remove the nut holding the fan blade to the fan motor and remove the fan blade. 9. Reverse the process, mounting the fan blade to the new motor, screw the motor to the bracket, screw the bracket to the vertical bracket, screw the vertical bracket to the refrigerator and plug the power connector back into the motor. I did not have to use any of the extra mounting hardware or electrical hardware provided with the kit. It might be a good idea to purchase a new fan blade with the motor kit, the fan blade can get pretty grungy. I cleaned the fan blade with some degreaser before remounting it.

First I called my friend Robert in Kissimmee, Fl to have an idea regarding the problem because I had never serviced a fridge before. Then he suggested that I check with PartSelect on the Web. Then PartSelect repair videos showed me everything. I followed step-by-step but the problem persisted. I finally realized that the airflow conduit between the freezer and the fridge was clogged with ice. I then proceeded to remove the ice underneath the coil on the aluminum cover and Bingo. The problem was in fact the ice. Well, I only spent $33 dollars for the non-necessary Bimetal Defrost Thermostat. I learned a great deal from that repair.

After watching the video it was a snap. Defrosting the freezer took the longest time. I used a hair dryer to melt the ice. Once the freezer compartment was clear of ice the removal and installation were a step by step procedure which the video showed in detail. It's been about a week since I installed the bimetal defrost thermostat and it seems to be working like new. Sure glad I researched this problem on the internet instead of calling a very expensive repairman! Thanks partselect. Com!!!

The icemaker came with very easy to understand instructions the installation took less than 45 min. that included installing the selinoid valve and waterline I had a nearby waterpipe, the acual icemaker took about 5 min. to install it in the freezer.

Pulled up part select video on u-tube. Followed instructions on dissambly of top freezer and found condensor freezing up blocking air from refrigerator. Checked timer to make sure it was good. Next checked continuity on heater to make sure it was good. Last checked bi-metal thermostat for continuity while cold. Found Bi-metal part to be defective (also rubber in top of was popped up which is a sign of a bad part). Simply ordered new part from Part Select, received in 2 days and replaced Bi-metal and melted ice with hair dryer and reassembled freezer. While waiting on part you can still use refrigerator by melting ice so air can get to refrigerator. I put a towel in bottom of freezer to catch water. Greg W. in Ga.

After ordering the ice-maker, but before it had arrived, I installed a valve in the pex water line in the room right below the fridge. I had to rent a pex clamp kit from Home Depot. It cost $8 for 4 hours and came with the crimpers and band cutters. I then ran a poly line to an in-line filter which I mounted to an exposed stud and fished the line up the wall and out a small hole I drilled behind the fridge. When the ice-maker came, it took less than 30 minutes to install and start my first batch of ice. With the in-line filter, the ice forms with practically no sediment flakes. Part Select was the only place I could find a replacement ice-maker. In addition to the parts in the ice-maker kit, I had to buy 12 feet of poly water line, a ball-valve, the in-line filter and a compression fitting. A total of $20 at my plumbing contractor store.

This problem can be caused by 3 different part failures. Timer, thermostat or heater. After contacting a service repair shop I was told that most often it is the thermostat. The cost of the repair would be at least $115. To much for an old refer. So I ordered the part from Partselect for $33. and put it in myself. Step1 cut the power to the refer. Step2 remove ice maker if you have one. Step3 remove base and back panels in the freezer. Step4 the coils were badly frozen so I used a hair dryer to thaw it out. Would have waited a long time for it to thaw out otherwise. Step5 The thermostat is clipped on to copper tubing next to the coils. Unclip it and cut the wires close to the thermostat. Strip the wires and wire nut the new thermostat. Clip it back on to the copper tubing. Put it all back together and start it up. It's over a week know and no problems. Note: We have whirlpool appliances that are over 16 years old. I have repaired the washer, oven, and now the refer with parts from Partselect. Good company. Always received the correct part within about 3 days from ordering. If you are able to do the work yourself you can save big bucks and keep your appliances running longer. Good Luck

Looked up the refrigerator model number, found parts break down and ordered wheel assy...thought it was the wrong but wheel size was right...read the instructions (good thing) and found out you had to slide entire bottom panel out 1/2 inch to access a hidden pin...did as the instructions said, slid out the bottom panel, found pin as advertised, removed pin, broken part fell out, replaced the wheel assembly, repinned, slid the bottom panel in (a bit more harder than getting it out), replaced all screws and was completed in about 40 -50 minutes. Good thing it came with instructions!!