1069650482 Kenmore Refrigerator - Instructions

Used the suggested problem list here to narrow down that the repair was most likely the run capacitor. Poped the new one in and I now have better control of my compartment ranges. I have a temperature gauge in each compartment. Check them every opening of the doors.

I just replaced my defrost thermostat after using the place-in-ice-water method, and I think it may not have been necessary. My timeline: my fridge was not getting cold enough. I realized it the day before going on a trip. I vacuumed the (very dusty) coils at the bottom, and the next morning the fridge seemed colder, but I thought I should order parts just in case. I ordered a heater and a thermostat. The fridge seemed to be operating normally when I returned from my trip, but I had the parts, so I thought I'd go ahead and dismantle the freezer and test the existing parts. My intention was to return both parts if the old ones passed the tests. I opened up the back of the freezer and there was no ice on the fins. I thought, great, the existing heater works! I cut out the thermostat, placed it in ice water, and didn't get continuity. So I decided to go ahead and put in the new thermostat. Because I'm not experienced with using a multimeter, I thought I'd test the new thermostat to see how the test should work. To my surprise, the new thermostat also failed the test! Stumped, I thought I might as well install the new thermostat, since I had opened the package and couldn't return it.
Further internet research suggests the place-in-ice-water method of testing is not adequate. One YouTube video by Parts Dr says to place the part in a working freezer. I froze my old thermostat and tested it; still no continuity. This thermostat may not be typical, though. The video discussed the temperature ratings on thermostats. The temperature rating on both (old and new) thermostats is L8.9-16.7C. That converts to 48-63 degrees fahrenheit, which obviously are not freezing temperatures. I'm not convinced I needed a new thermostat, but I trusted the videos I consulted earlier.
I cleaned the fridge thoroughly, so at least now I have a nice clean fridge to show for my efforts.

Installed ice machine components using kit and included instructions. Easy! Ran a copper line from under sink valve to back of refrigerator under the floor. Drilled two holes to run copper line. Plumber turned water off and replaced single valve with a double valve (one line to faucet and the other for the copper line). Installed shut off valve and filter at the other end of copper line. Then stainless hose to refrigerator. Everything went smooth. Double check the factory installed plastic line from the electric valve to the inlet for your freezer. Mine was barely inserted and leaked. I pushed it in all the way and it is fine now... Ice maker works really well! Wish I had done this sooner!

Removal of the door gasket went quite fast. First i needed a 8mm wrench. That what I didn't have. Got the socket set, not the wrench. Tried adjustable wrench, went slow. I slowly got the bolts out. Putting the gasket on was slow. Then I get to the last corner, was awful for me. I finally get it on. Putting the freezer door back on 1st went crazy. I finally looked on top of refrigerator, saw (3) bolts, removed them, installment went easy from there.

Easy ordering and installation.
Thanks.

I looked it up on the site per Refrigerator Model #. I wanted a confirmation from an expert at this site that I was ordering the right drawer. The part # the expert gave me was different than what I was going to order per my Model #. I'm really glad I waited for the expert reply and ordered that drawer. This is for a rental property, and we are a few hours away from the property. It was less than a minute to pull out the old crisper drawer and slide in the new. Thank You!!!!!

We went online, found the part, and had it delivered to our rental house in Nags Head, NC. It was the easiest thing ever.

Thank you

Replaced the part and put it in the refrigerator

Took everything out of the old one, lined the new one with cloth and put everything back in.

Replaced but drawers are lesser quality to the original drawers. Do not glide open easily

Work just perfect

Followed the directions. Installation was quick. Took loner to put the covers back on and push the applicance back in position than the repair.

Not a repair, only a new part.

Just like the video showed me.It still does not work. Have to turn it off and on to make it start up.I also replaced thermostat in freezer. Does not work.

pulled the old one out and put the new one in.