JC2225GEKB Jenn-Air Refrigerator - Instructions
Jump to:
Keep searches simple. Use keywords, e.g. "leaking", "pump", "broken" or "fit".
- Customer:
- Kerry from DE PERE, WI
- Parts Used:
- WPD7749401
- Difficulty Level:
- Very Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Screw drivers, Socket set
End Cap was broken and ice would not dispense.
Ridiculous how easy it was, REALLY!
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Marybeth from VACAVILLE, CA
- Parts Used:
- W11395888
- Difficulty Level:
- Very Easy
- Total Repair Time:
- Less than 15 mins
Lost cap for filter
Bought new cap.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Richard from PORT JERVIS, NY
- Parts Used:
- W11396033
- Difficulty Level:
- Very Easy
- Total Repair Time:
- Less than 15 mins
No problems
Just plugged it in
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Mary L. from Millsboro,, DE
- Parts Used:
- WP627843
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Screw drivers
Ice maker ejector arm broke into.
Removed old ejector arm and installed new part.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Carlton from CHICAGO, IL
- Parts Used:
- W11396033
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Screw drivers
Light out.
Popped out the old switch and replaced it with the one dying
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Daniel from SAINT ALBANS, VT
- Parts Used:
- WPA3223101
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Pliers, Socket set
Water line feeding ice maker was not producing ice
Take out the elbow fill tube and check to see if ice build up inside tube. Clean tube of ice build up. Replace tube back in. In my case that corrected my problem.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Debbie from Overland Park, KS
- Parts Used:
- WP67005959, WPD7749401
- Difficulty Level:
- Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Nutdriver
Ice maker would jam up and not let ice out thru dispencer .
Super fast , I received my parts the very next day ,THANKS to PartSelect.com. GREAT JOB .
Pulled out 4 screws , pulled out the ice turn gear & crusher , replaced the helix end cap , put all these parts back in place , screwed 4 screws back in ice bucket , back in freezer and it works like new . It would of cost me $110.00 to have a repair company do this simple job .
Pulled out 4 screws , pulled out the ice turn gear & crusher , replaced the helix end cap , put all these parts back in place , screwed 4 screws back in ice bucket , back in freezer and it works like new . It would of cost me $110.00 to have a repair company do this simple job .
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Tim from Berkeley, CA
- Parts Used:
- WP628356
- Difficulty Level:
- Easy
- Total Repair Time:
- 1- 2 hours
- Tools:
- Nutdriver, Screw drivers
Ice maker broken. Quick fix
The plastic fill cup part is also used to hold one end of the wire “one/off” switch that is manually activated or activated when the ice tray is full. This wire piece fell out because one end, that is part of the plastic fill cup, broke off. The wire switch was fine.
The video demos show you exactly what to do. The repair man showed me a trick to speed up the testing process. The trick is to insert a wire jumper cable to actuate the ice maker and make it rotate. But this isn’t necessary.
Hardest part of this fix is emptying the freezer (bottom with a slide out door) and removing the door.
Why this part is so expensive is beyond me. But I’m happy it was available for a 24yo fridge that still works!!
The video demos show you exactly what to do. The repair man showed me a trick to speed up the testing process. The trick is to insert a wire jumper cable to actuate the ice maker and make it rotate. But this isn’t necessary.
Hardest part of this fix is emptying the freezer (bottom with a slide out door) and removing the door.
Why this part is so expensive is beyond me. But I’m happy it was available for a 24yo fridge that still works!!
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- William from FAIRFIELD, VA
- Parts Used:
- WPW10503278
- Difficulty Level:
- Easy
- Total Repair Time:
- 30 - 60 mins
- Tools:
- Screw drivers
Unit would not defrost
I checked the element and the thermostat and determined the problem to be the control board. I simply followed the instruction in the video. Everything went well until the last step, the video said to push the freezer down button. When this did not work I refered to the written instructions which told me to push the up button. That did it. Job complete. The unit is working as it should.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- ROBERT from WESTFIELD, IN
- Parts Used:
- WP628356
- Difficulty Level:
- Easy
- Total Repair Time:
- 30 - 60 mins
- Tools:
- Nutdriver, Pliers, Screw drivers
broken hinge bearing on ice maker
Disconncted power, pulled plug on disconnect, loosened 3 ice maker attach screws, removed ice maker. carefully removed old broken part, to understand reasembly. Reinstalled new water fill & bearing part.. hung icemaker and tightened attach screws. Reattached electrical plug.. turned on power, it all worked. .took about 45 min to remove, 15 min to reinstall. Right tools needed re disassembly AND ASSEMBLY
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Larry from GOLDEN, CO
- Parts Used:
- WPW10503278
- Difficulty Level:
- Really Easy
- Total Repair Time:
- 30 - 60 mins
- Tools:
- Screw drivers
About twicw per year the freezer would ice up because the control board didn't activate the defrost element
Removed the cover using a mirror to see how to release the clips on the rear side of the cover, removed the circuit board noting how everything was installed and also visually verified the part was the same. Broke the circuit at the designated score, installed and followed instructions for programming. All is well now.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- john from TITUSVILLE, FL
- Parts Used:
- WP12665101
- Difficulty Level:
- Really Easy
- Total Repair Time:
- 30 - 60 mins
seal leaking
pull open seal lift up release bottem catch push in to release top catch clean disk and installnew seal put back in the reverse of taking out dont take any thing else apart
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- WESLEY from INDIO, CA
- Parts Used:
- WP67005959, WP12740302
- Difficulty Level:
- Really Easy
- Total Repair Time:
- 30 - 60 mins
ice bucket And crusher repared
bought new
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Robert from Meridian, ID
- Parts Used:
- WPW10503278
- Difficulty Level:
- Really Easy
- Total Repair Time:
- 30 - 60 mins
- Tools:
- Screw drivers
Lower freezer section was icing up, not defrosting properly. Repeated manual defrosting including disassembling did not solve the problem.
Emptied and disassembled the freezer. Defrosted and dried the coils. Tested the defrost heater coil ( 50 ohms ) PRT and fan - all OK. Opened the lower back panel and cleaned the water collection tray. Vacuumed out all debris including coils underneath. Reassembled everything. Removed the old control board and installed the new board paying attention to ESD steps. Applied AC power. Programmed the new board per the video link ( nicely done ). 3 weeks later and the unit seems dry and happy. Running at lower settings with good temperature results. Suspect the 24VDC relay activating the defrost heater coil on the control board or what controls the relay not working. May pull relay for test.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Edward from Reading, AL
- Parts Used:
- WPW10503278
- Difficulty Level:
- Easy
- Total Repair Time:
- 15 - 30 mins
- Tools:
- Screw drivers
Refrigerator was not cold.
Refrigerator was not cold.
I had this problem before and it was the control vale in the back of the refrigerator. I ordered it and change that out in 5 minutes. That wasn’t the problem. I had the repairman come over and within 5 minutes he told me what the problem was. He showed me where the control board was. He then walked me through the removal process.
First remove the light cover on the Freezer & Refrigerator in front where the light button is located. Pull down on the front of the light cover. It pops out.
Second, in the front of the freezer & refrigerator temp control panel put your fingertips in front of the panel and pull down it’s hard to get the pins to release but the front pins will release, then pull down a little to allow the back hooks to release. (You can use a small common screwdriver if you can’t get it with your fingertips).
Next, once the panel is removed then disconnect the wiring harness. Then bring the panel to the counter, this is where you remove the circuit card and replace it. There are 4 hooks that hold the circuit board in place. Use a small common screwdriver to push the hooks away from the board. The new board comes as one piece. The board is perforated to allow you to snap the board. Directions come with the board and how to snap it. You will need to pay attention on how you removed the board. You will need to put the new board in the same way it came out.
Once the board is re-installed and lock into position reverse the process and install the control panel back into position.
Next is the programing of the board. Follow the directions that come with the control board and you will be back in business
This task took about 15 minutes to remove & replace and to program.
I had this problem before and it was the control vale in the back of the refrigerator. I ordered it and change that out in 5 minutes. That wasn’t the problem. I had the repairman come over and within 5 minutes he told me what the problem was. He showed me where the control board was. He then walked me through the removal process.
First remove the light cover on the Freezer & Refrigerator in front where the light button is located. Pull down on the front of the light cover. It pops out.
Second, in the front of the freezer & refrigerator temp control panel put your fingertips in front of the panel and pull down it’s hard to get the pins to release but the front pins will release, then pull down a little to allow the back hooks to release. (You can use a small common screwdriver if you can’t get it with your fingertips).
Next, once the panel is removed then disconnect the wiring harness. Then bring the panel to the counter, this is where you remove the circuit card and replace it. There are 4 hooks that hold the circuit board in place. Use a small common screwdriver to push the hooks away from the board. The new board comes as one piece. The board is perforated to allow you to snap the board. Directions come with the board and how to snap it. You will need to pay attention on how you removed the board. You will need to put the new board in the same way it came out.
Once the board is re-installed and lock into position reverse the process and install the control panel back into position.
Next is the programing of the board. Follow the directions that come with the control board and you will be back in business
This task took about 15 minutes to remove & replace and to program.
Was this instruction helpful to you?
Thank you for voting!