PSS28KSHGCSS General Electric Refrigerator - Instructions
Jump to:
Keep searches simple. Use keywords, e.g. "leaking", "pump", "broken" or "fit".
- Customer:
- Carla from Sublette, IL
- Parts Used:
- WR32X32346
- Difficulty Level:
- Very Easy
- Total Repair Time:
- 30 - 60 mins
Bottom refrigerator drawer cracked tracks
Pull out old drawer and replace with new one.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Michael from WOODINVILLE, WA
- Parts Used:
- WR49X10091
- Difficulty Level:
- A Bit Difficult
- Total Repair Time:
- 1- 2 hours
- Tools:
- Screw drivers
Fridge too cold. Couldn't get it above 31F
The video was very helpful as the fridge used was close in configuration to ours. Only difficulty was installing the light tray assembly which on ours is two piece, a U shaped plastic tray into which the light assembly/electrical harness is attached. Re assembly was tricky as the plastic tray was flimsy and the light assembly kept coming out. Needed two pairs of hands but not enough room. The problem was solved by using blue tape to keep the complete assembly together, then gently removing it after the 4 mounting screws were in place. After that all went smoothly. Turns out the old damper assembly was broken. Since then the fridge has been working normally with set temp. of 37 holding steady and freezer at 0, per GE recommendations. Good fix!!
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Arthur from Sun Lakes, AZ
- Parts Used:
- WR12X10625
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
Broken front/handle on roll out freezer drawer
Just snapped the part in place. No tools needed
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Allen from The Woodlands, TX
- Parts Used:
- WR71X10764
- Difficulty Level:
- Easy
- Total Repair Time:
- Less than 15 mins
Broken module shelf insert
No tools needed. Snapped in place. Very easy.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- robert from scottsdale, AZ
- Parts Used:
- WR12X10625
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Screw drivers
easy
just snapped it on.. no problem
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Dennis from Liberty, MO
- Parts Used:
- WR49X10091
- Difficulty Level:
- Easy
- Total Repair Time:
- 15 - 30 mins
- Tools:
- Screw drivers
Refrigerator was too cold.
Remove all shelves and back duct work in refrigerator section. Remove 4 screws and electric door / blower section. Part was exact replacement. Refrigerator is working perfectly.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Gina from Hamilton, OH
- Parts Used:
- WR12X10625
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
handle broke off of freezer bin
simply snap it on to the drawer. Very easy
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Traci from Smithville, MO
- Parts Used:
- WR71X10764
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
plastic on one of the drawers cracked
snapped the old one out snapped the new one in.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Neal from Haverhill, MA
- Parts Used:
- WR12X10625
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
Freezer draw panel cracked
Parts easily snap onto the freezer drawers, that easy!
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Ann from Bath, PA
- Parts Used:
- WR12X10625
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
broken drawer pull in freezer
it just snapped on
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Troy from Council Bluffs, IA
- Parts Used:
- WR49X10091
- Difficulty Level:
- A Bit Difficult
- Total Repair Time:
- 30 - 60 mins
- Tools:
- Screw drivers
Food freezing in the refrigerated section.
It was pretty straight forward. Be very careful removing the top panel above the light, it slides forward about a half inch. Be gentle, the plastic tabs can be easily broken and then the top piece will sag and fall off easily. Everything else was screwed into place and pretty easy to take apart and put back together.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Stefan from Middle Island, NY
- Parts Used:
- WR49X10091
- Difficulty Level:
- A Bit Difficult
- Total Repair Time:
- 30 - 60 mins
- Tools:
- Screw drivers
upper rear of fridge too cold
I removed the light and cover, then removed the lower vent cover. This required a bit of pinching and pulling. Then I removed the Fresh Food Air Inlet Cover. I looked inside and saw that the flap/dampener was unseated and flopping around. That would explain why all the cold air was coming in from my freezer and freezing the food in my fridge. Replaced old with new, plugged in, reinstalled all covers, and Voila! My fridge is working correctly again. Thanks to the first review which was the one I followed. And Thanks to PartsSelect!
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Danny from Fairhope, AL
- Parts Used:
- WR71X10764
- Difficulty Level:
- Easy
- Total Repair Time:
- 15 - 30 mins
- Tools:
- Screw drivers, Socket set
Broken Handle
replace the broken handle
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Carol from Petaluma, CA
- Parts Used:
- WR49X10091
- Difficulty Level:
- Really Easy
- Total Repair Time:
- 15 - 30 mins
- Tools:
- Screw drivers
The refrigerator side was too cold freezing items
The thermostat was set at 0 for the freezer, but at 37 for the refrigerator. The refrigerator was showing a temperature of 20 degrees and would not stay at 37. After learning the 3 choices it could be (air inlet cover, thermostat, and computer), I went for the air inlet on the basis of percentage of repair. With this particular refrigerator with this problem; this is repair has the highest chance of success. Nice on-line decision making tool! I went with choices of previous buyers and followed previous buyers instructions. All I needed was a couple of Phillips head screw drivers, and cleaning the dirt I was finding in the refrigerator was the biggest job.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- erik from erie, CO
- Parts Used:
- WR49X10091
- Difficulty Level:
- Easy
- Total Repair Time:
- 15 - 30 mins
- Tools:
- Screw drivers
Our GE Monogram's freezer and flood locker compartments were too cold
This website is awesome! It basically tells you exactly what is wrong with your fridge. Our food side of the refrigerator was getting way too cold. Some items actually froze. I looked here and it said the fan/ damper assembly was broken. All I did was remove the part they said was broken and sure enough the little damper door that lets freezer air into the fridge side was broken. I ordered the part, replaced it and presto the refrigerator holds perfect temperature again! The replacement was super easy...only tool needed was a screwdriver and 15minutes! Thanks
Was this instruction helpful to you?
Thank you for voting!