TFXC24ELP General Electric Refrigerator - Instructions
Jump to:
Keep searches simple. Use keywords, e.g. "leaking", "pump", "broken" or "fit".
- Customer:
- Catherine from SEATTLE, WA
- Parts Used:
- 40A15
- Difficulty Level:
- Very Easy
- Total Repair Time:
- Less than 15 mins
The light inside the oven had burned out
0. As a safety precaution, unplug the range or hit the relevant fuse breaker before you start. You might also want to grab a flashlight. Definitely do not try to do this while the oven is hot.
1. Pinch the wire over the light bulb cap to remove it. This is inside the oven at the back.
2. Pop off the hemispherical glass cap.
3. Unscrew the old light bulb, and screw the new light bulb in its place.
4. Put the cap back.
5. Secure the cap by putting the wire back in its slots on the cap.
No tools needed, the cap is just held in place with pressure from the wire.
1. Pinch the wire over the light bulb cap to remove it. This is inside the oven at the back.
2. Pop off the hemispherical glass cap.
3. Unscrew the old light bulb, and screw the new light bulb in its place.
4. Put the cap back.
5. Secure the cap by putting the wire back in its slots on the cap.
No tools needed, the cap is just held in place with pressure from the wire.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Charles from Franklinville, NJ
- Parts Used:
- WR2X4901
- Difficulty Level:
- Easy
- Total Repair Time:
- 15 - 30 mins
- Tools:
- Screw drivers, Socket set
worn/broken cam , door doesn 't self close
Remove contents of door , Remove top hinge cover - phillips screwdriver , remove top hinge screws ( 2 ) - socket wrench , lift door off lower hinge pin , lay door on edge , remove cam retention screw ( 1 ) - socket wrench , remove broken cam , install new cam , apply vasaline to cam and hinge pins , repeat above steps in reverse . Door now self closes .
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Tony from Charlotte, NC
- Parts Used:
- WR57X10051
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Nutdriver
Water won't stop running in Ice Maker
Basically I looked online for some research thru google and found this great site.. A few other folks had the same problem as I had with mine and I figured that I would start with replacing the double outlet water valve.. So I ordered it from this site and in two days wow that's fast shipping.. This repair took less than 15 minutes to complete and talk about a big savings $ 45.00 for this repair job.... I'm really happy now.... It's pretty easy though.. simply unplug frig first... then remove screw holding the valve.. remove clips and have a bowl near by when remoing the two hoses... replace valve.. its all colored coded just match the colors and then the two hoses they are different sizes one for each hole... reclip the clips and then replace the screw and finally plug the frig back in.. and then turn on the water to check for leaks.. if no leaks you are done...
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- andy from clearwater, FL
- Parts Used:
- WR57X10051
- Difficulty Level:
- A Bit Difficult
- Total Repair Time:
- 15 - 30 mins
- Tools:
- Pliers, Screw drivers
Ice maker leaks water freezing ice cubes into one block
Googled the problem, find parts select.com, called service rep and the female rep recommended this part.
Ordered part, got it, replaced it and it works fine.
Note: the water hoses are just installed by pushing in, no tools required.
Ordered part, got it, replaced it and it works fine.
Note: the water hoses are just installed by pushing in, no tools required.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Robert from Bakersfield, CA
- Parts Used:
- WR2X4550
- Difficulty Level:
- Really Easy
- Total Repair Time:
- 30 - 60 mins
- Tools:
- Nutdriver, Screw drivers
Broken drive cup in the ice dispencer
Emptied the ice from tray.
Removed the four screws that hold the face plate.
Removed the four screws that fasten drive housing to the tray.
Slid the drive cup into place at the end of the auger.
Made sure the rubber gasket was in place .
Replaced the four screw that hold the housing to the tray.
Replaced the four screws that hold the face plate.
Put some ice cubes in the tray and tested to be sure everything worked properly.
Removed the four screws that hold the face plate.
Removed the four screws that fasten drive housing to the tray.
Slid the drive cup into place at the end of the auger.
Made sure the rubber gasket was in place .
Replaced the four screw that hold the housing to the tray.
Replaced the four screws that hold the face plate.
Put some ice cubes in the tray and tested to be sure everything worked properly.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Ann from LAPORTE, PA
- Parts Used:
- WR60X30349
- Difficulty Level:
- Easy
- Total Repair Time:
- 30 - 60 mins
- Tools:
- Nutdriver
freezer too cold and refrigerator not cold enough because fan not working
Had to defrost a bit and then was able to remove rear freezer panel by simply removing the 2 screws holding it in place.
Old motor easily removed from its mounting bracket. and replaced with the new. Had to use the two wires sent with the motor. I clipped off the male connectors and joined them with wire splicers to the black and red wires clipped from the old motor. Then reinstalled.
The replacement motor works great. I was afraid the old fan blade might not fit but it slid on perfectly.
Old motor easily removed from its mounting bracket. and replaced with the new. Had to use the two wires sent with the motor. I clipped off the male connectors and joined them with wire splicers to the black and red wires clipped from the old motor. Then reinstalled.
The replacement motor works great. I was afraid the old fan blade might not fit but it slid on perfectly.
Was this instruction helpful to you?
Thank you for voting!
The rail was chipped and wore from constantly using the drawer.
It was very simple to replace. I am not at all a mechanically inclined gal! Luckily it was simple and quick. Just two screws and the old one was out, then i replaced with the new one.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Steve from BRANDON, MS
- Parts Used:
- WR13X10020
- Difficulty Level:
- Very Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Nutdriver, Socket set
door hinge
put block of wood under the door, removed old hinge and installed the new one. about 15 minutes
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Gerald from WINTERVILLE, GA
- Parts Used:
- 40A15
- Difficulty Level:
- Very Easy
- Total Repair Time:
- Less than 15 mins
lights blown out
replaced lights in refrigirator and freezer
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- T from SOUTHBURY, CT
- Parts Used:
- WR60X30349
- Difficulty Level:
- Easy
- Total Repair Time:
- 15 - 30 mins
- Tools:
- Nutdriver, Pliers, Screw drivers
Original evaporator fan (31 years old) was making a lot of worn bearing noise
Empty freezer;
Remove shelves and ice trays;
Unscrew and remove the rear vertical panel;
Unscrew and remove fan housing;
Unscrew and remove fan from fan housing;
Fan blade slides off the motor shaft without tools.
Reverse order to reassemble with new fan motor.
I did have to use the wire extensions that were included as the replacement motor had the electric connections in a different location from the original motor.
Overall, this was an easy replacement.
Remove shelves and ice trays;
Unscrew and remove the rear vertical panel;
Unscrew and remove fan housing;
Unscrew and remove fan from fan housing;
Fan blade slides off the motor shaft without tools.
Reverse order to reassemble with new fan motor.
I did have to use the wire extensions that were included as the replacement motor had the electric connections in a different location from the original motor.
Overall, this was an easy replacement.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Joyce from Tacoma, WA
- Parts Used:
- WR2X9391
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
light wouldn't come out of socket
It just unpluged and the new one plugged in. Simple. The part was reasonable and arrived very quickly. It sure is nice to have a light in the frig again.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Joe from Woobridge, NJ
- Parts Used:
- WR50X55
- Difficulty Level:
- Easy
- Total Repair Time:
- 30 - 60 mins
- Tools:
- Nutdriver, Screw drivers
Ice build up in the evaporator coils and had to thaw it out with hair dryer
Cut old thermostat out and installed with heat shrinking wrap and solder the wires and still having issues it might be something else.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- David from CLIFTON, NJ
- Parts Used:
- WR60X187
- Difficulty Level:
- Really Easy
- Total Repair Time:
- 30 - 60 mins
Fan would not turn when the refrigerator came on all the time. Would physically have to turn the fan blades.
Did not do the repair because the unit arrived damaged. The packaging was in good condition. The plastic around the plug in shattered, and some of the plastic was inside the motor. Very good, and fast on adjusting the order.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Raymond from Niverville, NY
- Parts Used:
- WR17X2740
- Difficulty Level:
- Really Easy
- Total Repair Time:
- 15 - 30 mins
- Tools:
- Screw drivers
Blade on auger became stripped
Ordered at PartSelect and received the auger and blade within days. Printed the parts diagram and proceeded to take the auger apart the time it took would have been much less but I seized the opportunity to do a deep cleaning of the old parts before replacing them....The part diagram was the key to simplicity and the fast shipping was awesome. Thanks I'll be back....
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Jodi from Benton Harbor, MI
- Parts Used:
- WR23X37285
- Difficulty Level:
- Very Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Pliers, Screw drivers
Light out
Turned off the breaker to the fridge because I couldn't reach the power plug to unplug it . Use small flat head screwdriver to pop out the piece, disconnected the rubber prong connectors, inserted the new piece into the rubber prongs snapped it back into place. Flipped the breaker back on and prayed it worked. It did and I saved myself $120 service call.
Was this instruction helpful to you?
Thank you for voting!