PZS23KSEEFSS General Electric Refrigerator - Instructions

This part (plastic tubing) does not show up under my model of refrig...so I had to look thru the various water lines and pick the one that "looked" right. Luckily, this is the exact replacement part and works perfectly. I removed the lower back panel from the fridge, removed the bracket holding the water line connectors and pressed the outer ring of the coupler up until it released the old water line. I pushed in the new line, made sure it was snug with a gentle pull and ran the line under the fridge up to the existing coupler. I removed the old line from the existing coupler under the front left of the freezer door, and pushed in the new line. I did not need to use the new coupler. If my old line would not have been so brittle and cracked in several places, I could have just cut out the leaking portion and popped the new couple in to mend the line back together. Easy job and we can stop buying bottled water at the store now!

First, I turned off the water supply line to the refrigerator from the house at the wall and unplugged the power cord. Secondly, I removed the small screws that hold the piece of cardboard over the opening in the lower left corner (rear of the refrigerator) by the compressor. Thirdlyl, I removed the other end of the water line where it attaches to the water valve with an adjustable end wrench. Then I removed the small screw that holds the double water outlet valves to the refrigerator frame. I then removed the water valve by pulling it out of the rear of the refrigerator, unplugged the electrical connections, and cut the water lines where they enter the valves. I then plugged the electrical connectors into the new valves and pushed the hoses into their respective openings. These are one-way connectors - once you push them in (firmly) they will not leak or come back out. All I did then was replace the valve and secure it with the one little screw and then replace the cardboard piece onto the rear of the refrigerator. Don't forget to turn the water supply back on. That's it!!

Easy fix, but they don't give you plenty of wire to work with. When I pulled the switch out it only had about an inch of wire that came with it. meaning if I didn't have a grasp on the wires as I was removing the switch they would have slipped back up the opening

There were no fastening hardware. The plastic stripper just snaps in place. I had to be patient and could not get it out until I put upward pressure on the stripper.

This is the second or third time this cup has broken. Maybe we use more crushed ice than the average family, but you would think this part could be more durable. Anyway, I digress. This is about the repair. Four screws removed around bottom of tray, one screw removed for some bar that mechanically opens a door to allow ice to fall out of the tray, and two butter knives used to release tabs around the screw components... and we were done.

It was very simple! I assessed the situation and gathered my tools for the job. I used a flat head screwdriver, pliers, and electrical tape. I used the flat head screwdriver to release the switch from its location, the pliers to take the electrical terminations apart. I taped the wires individual so that I would not loose them in the door, also not to short them out. I then unpackaged the new switch to install. Pulled the tape off one of the of the terminals while holding the wire, and attached it to the new switchs terminal post. Did the same with the other wire, then snapped the new switch back into place. Immediately had results. I opened and closed the door a few times in amazement that something so annoying such as a light in your fridge could be so easy to fix. Most of all, having a business to rely on to find the part and deliver in a timely fashion. Thank you Partselect.com, you were outstanding!!!

Disconnect main water line from behind refrigerator
Remove bottom panel from refrigerator
Disconnect hose from water valve
Remove metal hose guard from top left of refrigerator Carefully remove plumbers putty from around filter hose (you will be reinstalling this putty around new hose assembly)
Inside refrigerator remove MWF water filter and guard, and then remove two screws holding filter assembly in place (this requires socket set with 4” extension bar)
Carefully pull filter hose assembly towards you from front of refrigerator. Once assembly is out remove Styrofoam cover from old assembly and install on new assembly
To reassemble, simply follow this process in reverse. Good luck

Raised side of fridge enough to get 1/4" ratchet with 1/4" socket under roller wheel assy. Removed three hex-head screws to separate damaged wheel assy from fridge frame. From panel below fridge compartment, backed-out stripped leveling screw. Mounted new roller assy and then threaded in new leveling screw from front. Lowered fridge and adjusted leveling screw for proper height. Suggest putting a 2x4 under fridge for safety when hands are under unit.

There is no access to the inside of the door to replace the water line. I was able to insert a 1/4" drip line barbed connector into the old line at the base of the door and then connect that to a piece of the plastic tubing which I then connected back to the original water supply tubing with the 5/16" union. It took three attempts to get the tubing through the bottom hinge without a crimp in it. It's best to have a second person to hold the door while you "fish" the tubing through the hinge.

Your instructions were "spot on"! Pried out broken switch with screwdriver-reinstalled new switch. Very easy! Ordered on line on a Wednesday new part arrived on following Saturday-Great service and will definately use again. Highly recommend PartSelect!

Removed tray, threw out ice , removed 3 screws used 2 screw drivers to seperate part & re installed

Followed the video showing how it was done. Took me longer to go to the basement and shut the water off and on, than it did to replace the valve

Tube was too short so I used the union to attach additional tubing to reach the valve at the lower rear of refrigerator

Shut off water supply. Unplugged refrigerator. Removed cover. (6 screws -- nutdriver will come in handy). Removed screw securing water valve to frame (again the nutdriver). Unplugged red and white power connectors to solenoids. Using channel locks, loosened nut holding main water supply to valve and removed. Depressed compression fittings to valve and pulled out plastic water lines that supply water dispenser and ice maker. Reconnected main water supply to new part. Pushed both water lines into respective fittings of new part. Reconnected power supply to solenoids. Attached new part to frame with screw. Replaced back cover. Turned water supply back on. Plugged refrig. back in. Problem solved! Savings = $300!

pulled out refer. found leak at corner lower back, pulled off lower cover. found valve for icemaker leaking. looked in owners/inst guide, pulled up on computer, identified part, called, order overnight part. recieved part & installed, repair complete & successful.