TFX22PRSBBB General Electric Refrigerator - Instructions

Unplug refridge then loosened two bolts holding old ice maker. Lower then unplug and removed. Plugged in new harness and tightened two bolts to secure new ice maker. Plug in frig and wait for ice.

My son did it , and showed me what he did when he was finished.

First I shut off the water supply and disconnected the power to the refrigerator. Remove the two finger tabs that are used to for the light swirch and ice/water by pulling straight down. Remove the cover to the dispenser assembly by pulling it out by hand. I removed the four small phillips head screw in each corner of the assembly. Pull the assembly out just enough to expose the circuit board connectors. Note the color of the wires and their position and location. The connectors are different sizes and should not be confused. Remove the two connector by pull them out straight. You can remove the entie assembly , but pay attention to the the water actuator when the assembly is removed entirely to prevent damage. Place the the dispenser assemby on a solid surface and remove the two screws holding the circuit board in place. Pay attention to the position of the black circuit board retainer be fore removing it. The circuitboard should be removed by pryiing gently on each side until it is released. Reverse the procedure for installation of the circuit board..

First I shut off the water to the refrigerator and unpluged the electrical cord. Then I unsnapped the cover to the control board assembly located above the ice/water selector knob. Then removed four screws holding the control board assembly. Then I tilted the assembly out far enough to unplug the two sets of wires connected to the control board. Then I removed the two screws holding the control board to the plastic assembly. You are then able to lift the control board out of the assembly. Be careful tilting out the assembly. I pulled too hard and removed the whole thing from the refrigerator which disconnected the ice/water actuator lever and I had some problems getting it re-installed correctly. Installation is basically the reverse of removal. I suggest testing it before snapping back on the final cover plate. I wouldn't recommend trying this repair unless you've done some kind of basic automotive or appliance repair... you can always try it and call a repairman if you get stuck. Good luck!

replacing the lines was easy, problem was the drawing on line and the parts list did not show two different size tubing used. had to run out for the 5/16 inche tubing for the water dispenser in the door. got the 1/4 inch tube done in 5 minutes.

The icemaker arm disconnected from the metal frame. This caused the icemaker to cycle and the heater to come on and stay on until the plastic parts melted causing a mess and stink. This action melted the ice and then the water fell through the frozen items in the freezer and refreezed in the lower portion. OK, I remover the dead icemaker and tossed it away. I installed the new icemaker and the wiring harness didn't fit right (way to long). I retrieved the old icemaker and removed the wiring harness from it. I removerd the new ice maker and installed the old wiring harness to the new icemaker. I then installed the new icemaker, plugged it in and turned on the power. No water, I ordered the dual solenoid water valve, installed it with difficulty (another story) the turned on the power. I reinstalled the ice bin and found it didn't fit. The icemaker was to low and couldn't be adjusted, 1/4" higher would have been great. I shoved in the bin anyway, I was out of ice for my scotch, and it started making ice.

instalation was very easy - but the part was 3/4 inch to long and a 1/32 inch to wide.Trimmed it with the "faithfull"
Dremel and it works!The instalation part of the "job" was less then 10 min.

Replaced icemaker assembly. Only 3 Phillips screws to remove the old assembly. Pretty much an exact swap. Was easy to replace but the connecting cable on the new replacement assembly wasn't very easy to make fit. Had to force it into a location that would be out of the way and allow everything to operate properly. That connecting cable should be more flexible and adapt to the fridge a little more friendly.

The solenoid that opens the ice chute would fire, but the ice auger would not turn in either direction. I verified that the motor was OK by running 120 V to it directly. Changing out the "timer board" was a 15 minute job and did the trick. Ice galore!

I received the part after doing what was instructed by process of elimination for the problem.I installed it and it still didn't work. I took the part out and called to return it but was told i couldn't because it was now a used part and your company only sells knew parts. Now, I have a circuit board that I have no use for.

Not really a repair. Just dropped it into place.

Would recommend this site to others ... comprehensive parts and descriptions, easy ordering and timely delivery.

Thanks much!

Basically I looked online for some research thru google and found this great site.. A few other folks had the same problem as I had with mine and I figured that I would start with replacing the double outlet water valve.. So I ordered it from this site and in two days wow that's fast shipping.. This repair took less than 15 minutes to complete and talk about a big savings $ 45.00 for this repair job.... I'm really happy now.... It's pretty easy though.. simply unplug frig first... then remove screw holding the valve.. remove clips and have a bowl near by when remoing the two hoses... replace valve.. its all colored coded just match the colors and then the two hoses they are different sizes one for each hole... reclip the clips and then replace the screw and finally plug the frig back in.. and then turn on the water to check for leaks.. if no leaks you are done...

Pulled out the fridge - unpluged. Water supply was already closed.
Then took off the cardboard cover in the back. Used a nut driver to remove 1 screw. Disconnected water lines and elec. connects.
Water lines slid into quick connects - connected electrical and mounted. Opened water suply needle valve.
Pluged in fridge did a quick test for leaks. Done in 5min.

we took off the old one and replaced it.

Installation could not have been easier!