TPX24BIBABB General Electric Refrigerator - Instructions

parts select delivery time unreal !!!!! ordered on a Tues. was here Wed !!!! Perfect fit, minor difference in tubing connection. Took more time to clean the floor once i moved the fridge than the actual repair. Thank you Parts Select, if i need more appliance repair parts, you're my first choice>

opened back panel and replaced valve verry easy

I watched the video on the partselect website once and completed the repair. Very easy!

I have never repaired anything before but I found your web site ordered the item and received it in 2 days Thank You,thank you

I removed the valve from the fridge with a nut driver, this allowed me to disconnect the two lines and the water main inlet. Re attach the main line and cut off ends of both plastic lines with a razor knife and re insert the two lines. Last was to connect the main water inlet and tighten . The last thing was to turn on the water and check for leaks and we had none so put the fridge back in its proper place and job done. Thank you for your help Michael

Fairly easy I pull the fridge foward and remove the backing board and notice the fan wasn't working, so I remove the fan and bench tested and it was burned then I clean the condenser with compress air if you don't have air then a vacuum cleaner works then once the part arrived I install it the now if working very good

remove the back cover where the valve is located, unplug the refrige, turn the water off. Remove the valve unit, cut the plastic water lines with the utility knife,unscrew the water feed. remove the unit. reasemble the new unit,install the water feed, connect by puching in the ice maker line and the water despencer line into the new unit.Plug the refrig back in and purge the water line. (done) saved a service call$$$$

I followed the instructions to the letter and it was very simple replacement even down to cleaning out the dust & dirt. The water dispenser works just fine now- Thanks for the tips

Replaced Valve - really easy repair -- longest part was getting fiber cover plate off and on back of refrigerator

I removed the old valve assembly from the refrigerator's cabinet with a nut driver. I then pushed the lines for the water dispenser and ice maker into the valve and attached it to the cabinet. After connecting the water supply we had ice and water.

Shut off water & elect to refg. moved refg out from wall. Removed back cover. disconnected water & electric connections. Removed old valve and installed new one . Plastic tube fit in same place elect pins (4) snapped in place. Used teflon tape when connecting copper plumbing to stop leaks. Also cut old tubing & replaced copper 1/4" compression ring. Note I ordered part before noon on thursday, part arrived fri AM 9:00 FedEx.reg service. cleaned up mess picked up tools. Refg worked like new. saved money on service call. Thanks

Ordered this part after i replaced the plastic tubes on the back as the problem persisted. loosen the nuts holding the water inlet lines, remove the cover to the valve. remove the valve and the water inlet line to the the valve. Disconnect the 2 outlets from the valve. 1 outlet to icemaker and other outlet to water cooler (bigger). Connect water inlet and 2 outlets to the new valve, test the water lines. Found the inlet is leaking, removed it and added teflon tape and reconnect it. All is done. Then I left the freezer door open for 3 hours to melt the ice on the wrong places and all is well.

1. Turn water supply off at wall. Unpulg referigerator. Remove all cardboard backing covering valve. Vaccum under ref. Unscrew water line where it attaches to valve on ref. (Reuse this later) unplug 4 electrical prongs. Mark with colored pen if not already color coded, so can put back correctly. Pull old ice maker and ref water supply out of valve if it does not screw in with nut. Cut very short peice off end of ref water lines. Slide new locks on water supply lines and push into water valve very hard to lock. Cant get them wrong as they are different sizes. Plug in electrical connectors same as you unpluged them. Connect water line to valve from wall. Turn water on and check for leaks. If none. Replace all screws on backing. Recheck for water on floor. If none congrads, just saved yourself about $120. 00 Labor. Take 2 asprin, drink a six pack and go to bed.

I pulled the Refrig out of the space so that I could get to the plug and water shut off. After unplugging and turning the water off, I had to remove the 7 screws holding the cardboard cover over the bottom portion of the Refrig. I then had to unloosen the water input to the the valve. Then I removed the screw holding the Water Valve. I then had to unplug the unit from the electrical connectors. After that I had to cut the plastic hoses off the valve. All that was left was to reconnect everything, replace the cardboard covering and do an operational test. Everything worked. The ice maker began to produce ice cubes and there were no leaks.

Took back off with sockets and saw water dripping from duel inlet water valve . Turned water off and had no trouble indentifying part with partselect via computer , ordered part using ups and received in two days , followed an excelent video furnished by partselect then replaced new part with old part , turned water back on and great ! I found it a lot easyier when you have your son-in-law do the work !