TFK25ZACGAA General Electric Refrigerator - Instructions
Jump to:
Keep searches simple. Use keywords, e.g. "leaking", "pump", "broken" or "fit".
- Customer:
- Terry from Channahon, IL
- Parts Used:
- WR13X10020
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Screw drivers, Socket set
Refrigerator side door feel off due to broken hinge pin
Followed easy video instructions. Loosened the necessary bolts, etc. Replaced hinge assembly, lined up door, lubed the hinge with vasoline. Works perfectly now. May purchase another assembly as spare as it appears this may be a common repair issue.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Fred from Scotts Mills, OR
- Parts Used:
- WR13X10020
- Difficulty Level:
- Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Socket set
Broken plastic closure cam
I blocked the bottom of the door(CAREFULLY!!) in position to elevate the door & take strain off the lower hinge & pivot post, while maintaining proper door alignment. I removed the two screws holding the hinge & post assembly from the frame, saving the screws & spacer for reuse. I removed the two screws holding the upper cam bracket on the door, again keeping the attaching parts. I installed and carefully aligned the new cam, original spacer & retaining plate to the lower edge of the door. I installed the new hinge & post assembly using the existing spacer & screws. I aligned the door & seal while checking the gap from top to bottom and from side to side. I carefully tighten the screws and rechecked the gap between the door & frame as well as the alignemnt of the door seal. Once satisfied with the alignment, I finished tightening the screws. I emphasize care and extreme caution in reinstalling the screws, they are a self-tapping (self-threading) type of fastener and this requires caution to make sure they are started and installed in the original threads of the door & frame. I put them all in using only finger pressure until I was positive they were started straight, going into the original threads, NOT trying to cross-thread or cut new threads, the structure is too thin for that and stripped threads will result! The door alignment and gap spacing is critical, make sure to check these adjustments carefully to ensure proper operation. Total time of repair, less than 15 minutes. I hope I have not over-simplified this because I have over 55 years of Automotive shop experienced and an ASE Certified Master Auto & Truck Technician...:-)
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Charles from Metropolis, IL
- Parts Used:
- WR13X10020
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Nutdriver, Socket set
Self closing upper and lower cam had broken
I removed the lower cover plate and placed a small scissor jack (used my car jack) under the refrigerator door, loosened the upper hinge, slightly raised jack to take the weight off of the lower hinge, removed the hinge with a 5/16 nut driver and the cam with a 5/16 socket. Installed new hinge and cam, removed door support and secured top hinge, check operation. Worked GREAT, did not have to remove door.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Alan from Richmond, VA
- Parts Used:
- WR13X10020
- Difficulty Level:
- Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Screw drivers, Wrench set
The refrigerator door wouldn't stay closed; it popped open when we tried to close it.
I followed the link to the how-to video that was provided on the parts-page, watched it and then followed the recommended steps. It couldn't have been easier -- and I'm not a "handyman." Thanks to PartSelect, I was able to diagnose the problem, find the part that was needed and figure out how to install it. I'm a grateful customer.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Alison from Lincolnton, NC
- Parts Used:
- WR13X10020
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Nutdriver, Screw drivers
Refrigeratior door of side by side would not close
I viewed a how-to video on partselect.com. I removed all items from the door shelves. Used a screw driver to remove the top "hinge" plate. Used a nutdriver to remove the door hinge plate. Removed door, laid on it's side-hinge side up (if you don't have a helper, lay it on a flat service). Simply removed the broken bottom plate and replaced with new part, and reinstalled on refrigerator. Super Simple!
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Tim from New Berlin, WI
- Parts Used:
- WR13X10020
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Nutdriver, Screw drivers
Refridgerator door was not closing properly
Followed the u tube video that was on the Part select website. Very easy install when following the video.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- John from Valdosta, GA
- Parts Used:
- WR13X10020
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Nutdriver, Screw drivers
Door Wasn't Closing All The Way.
Did the repair jut like the instructions on the web site stated. There was a good video for doing this repair. Looked at it a couple of times and did the repair right off the bat. Thanks folks.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Barbara from Apache Junction, AZ
- Parts Used:
- WR13X10020
- Difficulty Level:
- Really Easy
- Total Repair Time:
- 15 - 30 mins
- Tools:
- Screw drivers, Wrench set
lower hinge broken
removed door, replaced hinge, replaced door.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Connie from Woodstock, GA
- Parts Used:
- WR13X10020
- Difficulty Level:
- Easy
- Total Repair Time:
- 15 - 30 mins
- Tools:
- Nutdriver, Pliers, Screw drivers, Wrench (Adjustable)
Freezer side door would not close
Followed the video to replace bottom hinge assembly. The only hiccup was that the video instruction was for the fridge side door, so there wasn't step by step instruction for dealing with the electrical connection at the top of door or the water line at the bottom. However, it was simple enough to figure out. Replacement took about 20-25 mins.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Larry from Ogden, UT
- Parts Used:
- WR13X10020
- Difficulty Level:
- Really Easy
- Total Repair Time:
- 15 - 30 mins
- Tools:
- Nutdriver, Screw drivers
Broken Cam on Bottom of Freezer Door
Removed door with little or no difficulty. Only time consuming portion of repair was disconnection and reconnecting of water line to door. This difficulty was primary due to age of the unit. After repairing, I determined that the cam on the refrigerator was also damaged so ordered same part to replace the refrigerator side.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Brenda from Colleyville, TX
- Parts Used:
- WR13X10020
- Difficulty Level:
- Really Easy
- Total Repair Time:
- 15 - 30 mins
- Tools:
- Screw drivers, Socket set
Door would not stay closed
This was a Mother/Daughter feat. We viewed the video based on the bottom hinge assembly part that we had ordered. We did it exactly as shown and it was so easy. But while we had the door off we also had a chance to really clean the frigerator inside out. We were extremely happy that we were able to repair the frigerator oursleves and how much money we had saved by doing it. Thanks
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- hs from kathleen, GA
- Parts Used:
- WR02X10140
- Difficulty Level:
- Really Easy
- Total Repair Time:
- 15 - 30 mins
- Tools:
- Nutdriver, Screw drivers
door would not close on its own
like the man in the cd
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Ruby from Riverton, KS
- Parts Used:
- WR13X10020
- Difficulty Level:
- Really Easy
- Total Repair Time:
- 15 - 30 mins
- Tools:
- Screw drivers
Because the bottom hinge was worn out I couldn't close the door without lifting it first
After receiving the part (quickly) my son-in-law replaced the old one without any trouble. Thanks very much
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Brian from Newcastle, ME
- Parts Used:
- WR13X10020
- Difficulty Level:
- Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Nutdriver
Refrigerator door wouldn't close fully
This is a side by side freezer/refrigerator, nearly 30 years old. The repair was very quick and easy. 1. Remove two screws from top bracket. There is no cover for the top hinge on this older model. (2) Lift off door and set on kitchen table. (3) Remove two screws holding bottom door hinge. (4) remove two screws hold the cam and shims on the bottom of the door. (5) replace the broken cam on the door, and the bottom hinge assembly. (6) Replace the door on the bottom hinge. (7) Re-attach the top hinge screws, making sure the door is parallel to the freezer door. It took about 10 minutes to do all of the above. Best yet, I ordered the kit about 10am on a Monday, and the parts arrived, normal delivery, before noon the next day.PS- I used petroleum jelly to grease the hinge before replacing the door. The only tool I needed was a nutdriver.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Bruce from Ore City, TX
- Parts Used:
- WR13X10020
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Nutdriver, Screw drivers
Freezer side door would not remain closed
I did exactly as the video instructed. Removed the top hinge bracket. Removed the door. Replaced the parts on both the door and the freezer, taking care to save and re-install the shims. I put the door back in place and installed the top hinge. I also lubed the hinge pins with very light grease. The door now works perfectly.
Was this instruction helpful to you?
Thank you for voting!