TFK25ZACGAA General Electric Refrigerator - Instructions

This is a side-by-side unit. After blocking up the closed refrigerator door to the correct height to match the freezer door, I removed the lower hinge pin assembly by taking out two bolts. Save the shims (my had two) for the new hinge pin. Then remove the cam riser from the bottom of the door by taking out two bolts. Install the new cam riser on the bottom on the door. Then install the new hinge pin assembly. Total time 15 minutes.

blocked up refrigerator door.removed old hinge, and put new one on,with socket set.

I replaced both bottom hinges on my GE refrigerator. The hint that they were worn out was that both the freezer door and fresh food door would not close completely. You had to lift the door on the hinge to get it to close. Many of the GE service repair people recommend complete removal of each door to replace the bottom hinge. I found I could use a couple of wood blocks tall enough to take the weight of the door, jacking it up off of the hinge so could loosen the hex head screws. The freezer door hinge took a few minutes longer because the water supply line for the icemaker which is routed through the tube in the hinge. Overall, an easy repair and the cost of two repair visits was saved.

Empty all the good stuff stored in the door. Remove top hinge, lift off door. Remove bottom hinge from door and refrigerator, replace with new hinges. Replace door and reinstall top hinge. Very simple. Worst part was removing all the stuff stored in the door then putting it back! My parts arrived very quickly and I'm very pleased with Part Select.

There were some great posts on similar repairs that made me realize that it was best to get the whole hinge assembly. The video regarding the repair was completely accurate down to the size of the socket wrench required.

As suggested by your web site. Thanks. BC

Followed the video to replace bottom hinge assembly. The only hiccup was that the video instruction was for the fridge side door, so there wasn't step by step instruction for dealing with the electrical connection at the top of door or the water line at the bottom. However, it was simple enough to figure out. Replacement took about 20-25 mins.

Removed top hinge, lifted door from bottom post. Removed post with nut driver/socket, removed corresponding bracket/receiver from door. Attached new parts to refrigerator base and bottom edge of door. Was careful to replace part pieces in the same order as original, and secured tightly. Lifted door onto bottom hinge post, leveled the door and replaced top hinge.

Several months ago I had to replace the hinge and cam on the refrigerator door and the repair went smoothly as pictured in the video. This time I had to replace the cam on the freezer door so I ordered the hinge assembly, which included the cam. The web site confirmed that, according to the model number of my 27 year old refrigerator, the hinge assembly would fit. The problem I had was that the top hole in the hinge was positioned too high to fit the hole in the refrigerator so I had to put the old hinge back on, even though it showed some wear. The door closes smoothly by itself now.

Removed freezer door, put a blanket over the opening to keep food frozen. Installed hinge and replaced door.

Watched PartSelect video and did exactly as video said. Had finished product in less than 30 minutes.6 bolts and one screw.

I watched the "How To" video on the Parts Select web site twice. The video was very helpful, kind of like having someone right there with you showing you how to replace the hinge. I emptyed the door shelves, removed the top hinge hexscrews and easily lifted the door off the lower hinge, pieces of the broken cam hinge on the door fell off. I set the door on the floor in front of the sink with the handle edge on the floor. I unbolted the hinge and installed the new one. I loosened one screw on the door cam hinge and removed the other, easily replacing the broken part. Before tightening the screws I checked to make sure the hinge hole in the door was not blocked by the new cam hinge. I lifted the door and water ran out from somewhere. I tried to set the door on the lower hinge several times with no luck. I rechecked the hole, it was still clear. I tried placing the door on the refrigerator using the seal to hold it in place, that worked but I couldn't get the door to drop down onto the hinge. I played with it some more and finally got it in place, reinstalled the top hinge, mopped up the water and tried the door. It didn't self close. I adjusted the top hinge a couple of times and applied a little silicone to the hinges, it still didn't self close. I told my wife to make sure the door closes completely and reloaded the stuff into door. After a couple of days it now closes by itself like it's supposed to. In retrospect, I was alone doing the replacement and it really was an easy job but a second person to help line up the lower hinge would have helped a lot.

shimed the door up to its proper level. removed plastic cam from bottom of door with a socket disconnected the water line fitting and clamp. with a nut driver removed the hinge assy from cabinet being careful i sled the hinge assy off the plastic water line being sure not to kink the line, sled the new hinge assy back on the water line and mounted the new hinge assy to the cabinet and connected the water line back up and turned on the water and checked for leaks, all went well. place the bottom grill cover back on.

Followed directions in your video. Very helpful. Be certain to pay strict attention to how old part is removed. Had a little trouble replacing door on lower pin/hinge. Helps to have a little assistance. Good suggestion from another customer: get the kit.

I found you web sight. Determined I needed the hinge assembly. Followed the instructions in the video on your web sight, and it was all better.