TFK25ZACGAA General Electric Refrigerator - Instructions

Part Number: PS290199

1. Empty the door shelves.
2. Leave the door closed.
3. Remove the grill directly beneath the doors.
a. It snaps in. Pull simultaneously on the outside edge and the bottom about 2 inches in from the outside edge.
4. Using two people. One holding up on the bottom of the door. The other removes the two screws that hold the hinge to the refrigerator.
5. Open the door slowly and let it down slowly to pull the door away from the top hinge.
6. Replace the new hinge half on the bottom of the door. Insert the other half of the hinge into the hole of the door to keep the other half lined up while tightening the screws.
7. Apply a small amount of lithium grease to the contact surfaces of the new hinge.
8. Using two people. One person is to hold the door. Best if he/she holds it from the bottom. The second person lines up the top while pushing up on the door to insert to the top hinge.
9. Insert the other half of the new hinge into the bottom of the door.
10. Line up the holes and insert the two screws that hold the bottom hinge to the refrigerator.
11. Reinstall the grill.

Used (2) 2 x 4's as block and lever to raise door removed 2 screws and removed door used same socket to remove and replace door side of replacement part. replaced door. This is the second time I have replaced this part on frig. side. Very easy replacement.

I pulled all the items out of door, removed door top hinge cover, lifted the door off the hinge and removed the bottom hinge and closing cams and replaced them and re hung the door, just about that fast.

PS
Thanks for the parts

Being as the part is plastic it has a limited life span. But the repair is very easy and anyone can do it. I just proped the door with 2x6's and 1x2's and bolted it in. If you get confused just look at the freezer side to see how it goes, they are the same. It's four bolts and some shims that need to go in the same locations. I'm real happy that there is an online location to get these parts as there is not anywhere to get them where I live.

Emptied contents from the door. Removed top hinge cover (one screw) and top hinge (two bolts.) Lifted door off and replaced broken cam riser on bottom hinge. Put door back on.

1. Blocked up the door keep it steadily and enable ease access to screws.
2. Removed screws holding the door closing cam and lower door attach bracket.
3. Disconnected clamp holding the water supply line for the water and ice dispenser and disconnected the water line at the joint.
4. Removed the broken cam and put the new one in it's place, threading the water supply line through the hole of the cam.
5. Put everything back together in reverse sequence of removal.

Part no. Ps290199 received matched part no. Ordered, which I obtained from your web site, however, part did not exactly match oem part. It was necessary to drill a new top hole in each of the hinges. New hole center was drilled 1/2" off (lower) then hole in supplied part. Jpb could have been accomplished easily by the avg. Homeowner, but the drilling required a little more skill & possible some tools that an average homeowner does not possess. Otherwise job was relatively easy and satisfactorily completed.

Removed the refrigerator door. Replaced the cam riser bushing on the bottom of the door. I then removed the hinge bracket on the bottom of the refrigerator after removing the grill (oh yuk, what a mess under the refrigerator). I put the new bracket on and replaced the door. All is working well again. Thanks for the hints and the parts.

My job pretty much paralled the no. one on this list,I am a retired industrial electrician and have many years experience doing similar jobs.Went very well. . Tom Pennington of Muncie Indiana

This door was a problem for 1-2 years before I realized it had dropped about 2 inches. On close examination I saw that the hinge parts had completely broke down.
Had original manual-looked up model # on line under GE appliance and was surprised to find a large complete parts dwg showing parts I needed. Decided I needed the hinge assy.
Removed the door cap on top,replaced hinge assy and remounted door in reverse.--Works like new.

The on line "how to" video was PERFECT! I followed the steps and the repair was a breeze. Parts Select is now bookmarked in my favorites! These guys make is SO easy for "non-handy" folks like me.

It was really easy for me....my son told me what part I needed. I ordered it, and he installed it!

Removed top hinge assembly to pull door away from bottom hinge (2x hex bolts) Discovered that the pin on the bottom assembly had broken off. Removed and replaced bottom hinge assembly (2x hex bolts). Aligned door with top and bottom hinge pins. Tightened all hex bolts. Done

I followed the many post on replacing this part and everything went well. I had a little trouble getting the hinge post into the new hinge assembly, but with a slight adjustment it fell into place. I checked to see what tools I would need to do the job and had them ready before I even started. I removed the door and had it back on in maybe 10 minutes and I am not exactly Mr. Fix It. The only advice I can add to what everyone else has said is you should look the job over a little before you take the door off and have your tools ready. Then you won't have the door off for too long. I'd like to thank this site and everyone who gave advice on how to fix this problem. It made the whole job very easy.

I can not find the bill therefore I do not know what part I installed, as I keep installing parts in my home. I believe you are referring to a Vegetable Bin of my GE Refrigerator and you do not have to be a rocket scientist to install a new one.

Sorry
Abraham Zighelboim
PS: I just saw that was the Veg Bean