TPJ24BIBAWW General Electric Refrigerator - Instructions

Got a new valve

I removed the valve from the fridge with a nut driver, this allowed me to disconnect the two lines and the water main inlet. Re attach the main line and cut off ends of both plastic lines with a razor knife and re insert the two lines. Last was to connect the main water inlet and tighten . The last thing was to turn on the water and check for leaks and we had none so put the fridge back in its proper place and job done. Thank you for your help Michael

I pulled the refrigerator away from the wall. I turned the water supply valve off. With a nut driver I removed the screws holding the flexible cover on the back of the refrigerator, and set it aside. Next, again using the nut driver, I removed the screw form the clamp holding the copper tubing to the back of the refrigerator. Using a 1/2 inch open end wrench I took the copper tube off the water valve. Then, using the nut driver I removed the screw which holds the valve in place. I then unplugged the electrical wiring,and removed the two flexible tubes. I pulled the compression nuts from the flexible tubes, and inserted them into the new water valve, re-connecter the electrical wiring plugs, mounted the new valve to the refrigerator, reconnected the copper tubing to the new valve, turned the water supply valve on to be sure there was no leaks, secured the copper tubing to the refrigerator replaced the flexible cover, and then moved the refrigerator back in it's original position.

I turned off the power and water supply to the refrigerator Pulled fridge out,found leak at water valve. Removed valve,got on internet found partsselect and was able to match it up by model and picture. It was a lot easier than I expected it to be, thanks to the pictures. I ordered the part on Sunday night and got it Tuesday. Unbelievable. Put it in in about 10 minutes and drinking cold water with ice cubes again. The fridge wasnt down long enough to acually run out of ice. the fridge is 12 years old and keeping its maintenance low is a priority. If I had to hire a repair service we would probably thought seriously about replacing it.

Easy easy easy. Pulled the refrigerator out. Took off the old valve, cleaned around the connection, installed the new one, connected the tubing, turned on the water, connected the electrical connections, plugged it back in, checked for leaks, and walla...got water...Thanks for the help and great service. I even received the valve shipped standard delievery via Fed ex couldn't afford the overnight, and received the part next day... GREAT!!It took me 15 minutes to complete.

Uninstallrd old part by dis assemble. Then installed new part very easy access and installation

I have never repaired anything before but I found your web site ordered the item and received it in 2 days Thank You,thank you

remove the back cover where the valve is located, unplug the refrige, turn the water off. Remove the valve unit, cut the plastic water lines with the utility knife,unscrew the water feed. remove the unit. reasemble the new unit,install the water feed, connect by puching in the ice maker line and the water despencer line into the new unit.Plug the refrig back in and purge the water line. (done) saved a service call$$$$

Unplug the refrigerator. Remove the bottom panel the locate the valve on the left side of the refrigerator. Remove the valve. Unplug the two electrical connecters, then remove the two water lines. (At this point there will be a little water escape). Then replace the lines in the new valve, replace the electrical plugs and reassemble the bottom panel.

Recently changed the "under the sink" water filter because ice was getting really small-the filter was old. Ran great for a month or two. Then.....no ice. Water pressure ok. Even filled the ice tray in the ice maker and when frozen it kicked it out.....but no more. Repair took 15 minutes......pretty easy. When I called local appliance repair......they estimated it would cost $200-$250. My part was $44.

I'm a real novice at appliance repair but learned a lot from this effort. After doing enough online research and watching videos, I diagnosed the problem with my 20 year old ice maker. It was working, just not getting water. So I ordered a new water valve, much cheaper than the part Sears recommended. I easily hooked up the new valve but the old copper water supply line was leaking so I ordered a $7 pex line from Home Depot. Hooked it all back up and now I'm in business, and saved some money too!

Repair was really easy, bought the part because of partselect video. Saved myself a lot of money vs calling a repairman.

turned water off removed old water valve moved wires to new one moved water supply and discharges to new one reinstalled new valve

I used the how to video from the site and had the part replaced in about the same time the video did it, even with being distracted with a phone call.

Took back off with sockets and saw water dripping from duel inlet water valve . Turned water off and had no trouble indentifying part with partselect via computer , ordered part using ups and received in two days , followed an excelent video furnished by partselect then replaced new part with old part , turned water back on and great ! I found it a lot easyier when you have your son-in-law do the work !