TPS24PIBABS General Electric Refrigerator - Instructions

remove the back cover where the valve is located, unplug the refrige, turn the water off. Remove the valve unit, cut the plastic water lines with the utility knife,unscrew the water feed. remove the unit. reasemble the new unit,install the water feed, connect by puching in the ice maker line and the water despencer line into the new unit.Plug the refrig back in and purge the water line. (done) saved a service call$$$$

Fairly easy I pull the fridge foward and remove the backing board and notice the fan wasn't working, so I remove the fan and bench tested and it was burned then I clean the condenser with compress air if you don't have air then a vacuum cleaner works then once the part arrived I install it the now if working very good

parts select delivery time unreal !!!!! ordered on a Tues. was here Wed !!!! Perfect fit, minor difference in tubing connection. Took more time to clean the floor once i moved the fridge than the actual repair. Thank you Parts Select, if i need more appliance repair parts, you're my first choice>

opened back panel and replaced valve verry easy

I watched the video on the partselect website once and completed the repair. Very easy!

I have never repaired anything before but I found your web site ordered the item and received it in 2 days Thank You,thank you

Repair was really easy, bought the part because of partselect video. Saved myself a lot of money vs calling a repairman.

turned water off removed old water valve moved wires to new one moved water supply and discharges to new one reinstalled new valve

I used the how to video from the site and had the part replaced in about the same time the video did it, even with being distracted with a phone call.

I noticed water leaking from the bottom right rear of the fridge. I figured it was from the ice maker feed as I don't have the ice water feature on this GE profile. I shut the water supply off, ordered the part and received it in a few days. The defective part was easily accessible after I removed the cardboard cover. I removed the copper feed and unscrewed the old valve with a nutdriver. The new part fit perfectly, and even though there were instructions in the part to use the old bracket. the plastic water feed fit into the ice maker compression fitting with ease. I ran into a problem when I re-installed the copper compression fitting on the new valve,as I could not stop a leak from the top of the compression fitting. When my plumber originally installed the copper line he used enough pressure to deform the compression sleeve that slips over the copper tube. I had a couple of them in my "parts" drawer, so I took my tubing cutter and took 1/2" of the end of the copper supply line; slipped the new sleeve and re-installed the compression nut over the valve....fit perfectly. Turned on the water supply; no leaks. Checked the icemaker about 4 hours later and it made the first tray of ice. If I didn't have to deal with the water supply leak at the fitting, the job would have been finished in 30 to 45 minutes.

Removal of old part was very easy. However, there had been some new changes to the new valve. The prongs on the dispenser solenoid are narrower than the original so the push on connector would not grasp the prong and kept falling off. I finally was able to squash and crimp the pushon enough to make it stay on . Also, the waterline connection was changed from a compression nut with flared tubing end to a much easier cap nut and copper compression ring. This required a trip to the hardware store to buy the cap nut and ring and also required cutting the tubing above the flared end to remove the compression nut. Once this was done, the reassembly was simple. The required time would have been about 20 minutes if I didn't have to go to the store and redisassemble three times to reconnect the water supply solenoid push on..

Replaced valve with only one difficulty - the electrical spade connectors were different size. Did not come with adapters, as described on the web site.

Shut off water & elect to refg. moved refg out from wall. Removed back cover. disconnected water & electric connections. Removed old valve and installed new one . Plastic tube fit in same place elect pins (4) snapped in place. Used teflon tape when connecting copper plumbing to stop leaks. Also cut old tubing & replaced copper 1/4" compression ring. Note I ordered part before noon on thursday, part arrived fri AM 9:00 FedEx.reg service. cleaned up mess picked up tools. Refg worked like new. saved money on service call. Thanks

1. Turn water supply off at wall. Unpulg referigerator. Remove all cardboard backing covering valve. Vaccum under ref. Unscrew water line where it attaches to valve on ref. (Reuse this later) unplug 4 electrical prongs. Mark with colored pen if not already color coded, so can put back correctly. Pull old ice maker and ref water supply out of valve if it does not screw in with nut. Cut very short peice off end of ref water lines. Slide new locks on water supply lines and push into water valve very hard to lock. Cant get them wrong as they are different sizes. Plug in electrical connectors same as you unpluged them. Connect water line to valve from wall. Turn water on and check for leaks. If none. Replace all screws on backing. Recheck for water on floor. If none congrads, just saved yourself about $120. 00 Labor. Take 2 asprin, drink a six pack and go to bed.

I removed the old valve assembly from the refrigerator's cabinet with a nut driver. I then pushed the lines for the water dispenser and ice maker into the valve and attached it to the cabinet. After connecting the water supply we had ice and water.