GALLITO General Electric Refrigerator - Instructions

I just followed the directions carefully, loosened the screws with a nutdriver removed the unit from the screws, unplugged the unit from the freezer plug, took out the new unit, used the adapter supplied with the unit to match up with the plug in the freezer, carefully attached the icemaking unit to the screws, carefully slid the cord behind the unit, lightly clinched down the screws, checked it with a level and then did the final snug down. turned the unit on and it worked fine. Pretty easy, just take your time, don't rush and it will come out fine.

Super easy, had my 15 year old do it (with my supervision).
Followed very clear Instructions that come with the replacement...
But, he could not get to the plug location until he removed 4 screws holding the motor assembly that spins the ice in the drawer and moved it out of the way...
Followed the rest of the instructions...
Works like a charm.

looked up how on you tube and didn't find it just for the part but keep looking and saw how to replace other part that was behind touch pad so was easy from there on :)

Removed mother board and replaced. Working fine now

Instructions that came with the part were useless. I would have created new problems if I had attempted to follow the instructions. However, once I had the old part removed and put it beside the new part, required repair process was obvious, easy and quick. Frig now makes ice better than it ever did.

Watched the video that showed how to disassemble the ice maker. Then went right in and replaced the part and turned it on. It immediately started filling up the ice tray. I still have not been able to find out why it does not make as fast as the original ice maker. The tempeature for the freezer is set pretty cold.

After what I thought was a thorough troubleshooting of said problem I replaced the Water Valve Assy which was really easy as the video shared, but it did not fix my problem. I had forgotten to pull the water line apart at the coupling below the doors (this was a troubleshooting step in another area). The water not dispensing was due to the line being frozen! Putting all items in a cooler with a couple blocks of ice and leaving the freezer door open for the length of watching a movie, the water was flowing again. Still no ice though. Ice maker vs mother board at the rear of the fridge, Hmmmm. Went with the ice maker, watched video, ole Steve makes the plugs disconnecting look easy, I had to use a flat head screwdriver to open the clips (he doesn't mention that) and I had 4 screws where he had 3. Also he didn't mention about the instructions which gives you 3 options with your unit. I had to re-use my Plastic Stripper Plate along with the Fill Cup and Ice Maker Insert. After completion of installation and about a half hour later, I heard ice fall, Wooohoooo!!! Overall the experience will make me think to utilize PartSelect again when needed. Reasonable prices and decent shipping time. Now the freezer light is out...

First of all unplug refrigerator. Removed cover plate at lower rear of refrigerator. Marked and unplugged connectors. squeezed plastic projections with pliers to release board from refrigerator making sure not to break them. Reattached new board over plastic projections and reconnected plug in electrical connectors. Reattached cover plat making sure the ground wire is placed back under top middle screw. Plug in the refrigerator making sure the water in turned on before sliding the refrigerator back in place. Wait for ice to drop. Less than an hour.

It was exactly as shown in your instruction video

Reviewed video which was very helpful. Loosened two philips head screws, lifted up ice maker, unpluged power suppy and reinstalled. One of the easiest replacements ever!!

I rolled out the refrigerator, unplugged the cord and unscrewed the 8 screws to gain access to the main control board. I had to squeeze 4 white hangers to get the unit off. At first I thought you turned them which was a little confusing. Once the mother board was hanging I removed the connections which was easy. I did put the right ones on first and had to take them off because the left side would not reach. Suggestion would be to put the left side connectors on first which I did the second time. I slipped the control board back on the white clips and replaced the panel. I plugged the refrigerator back on and it has been working perfectly for the last two weeks. By doing the repair myself I saved $290. Thank you very much. Also I was impressed that I had the part in my hands two days after it was ordered and the shipping cost was on $7.49. I would definitely use Parts Select again if needed. Thank you again.

Went to GE website and researched the problem for the model, determined that it was 90% sure it was the Ice maker, I ordered it and it arrived the next day, installed it and it began working immediately,