GALLITO General Electric Refrigerator - Instructions

I had to defrost the freezer to free the icemaker. After that the installation was plug and play with two small exceptions: 1) I had to file down the width of the left hand tine of the old stripper so that it would fit the new icemaker, and 2) the motor housing of the new icemaker was slightly wider than the old one. It fit, but just barely. But I'm back in the ice again, no dripping water, all is good.

Installing the actual ice maker was quite easy. What takes most of the time is preparing the freezer for the install. Need to remove all shelving, (and the door) to gain access to the unit. The ice maker is simple to install once access is achieved. Putting everything back together takes some time.

I took off the front cover of the icemaker assembly and found that the gears were not meshing properly and therefore slipping. I removed the front panel and found that the white plastic cam unit under the large gear wheel had disengaged from the hole in the front plate which is why the gears were slipping. I refitted the cam and wheel and it worked fine but stopped again for the same reason the next day. As the plate appeared to be buckled somehow (not user repairable) and, as the unit was leaking and pooling water (which froze) in the collection unit, I decided to change the whole icemaker.

Ordered about 1300 on a Thursday, it arrived the next day at noon and was fitted straight away. As others have mentioned, the extension cable required to fit into my old fridge made it quite cumbersome however with a bit of juggling and persuasion, I got it to fit into the cut out corner of the ice container so it is completely out of the way. Job done in about 35 minutes, making ice in an hour.

I watched the video and then read the instructions. Emptied and cleaned freezer compartment. Removed old unit and removed part of old unit to be used in new installation. I then installed the new unit and turned the water back on. I let the unit produce over night and through the first batch of ice away. Because of the various regrigerators this ice maker was used I had a little confusion recognizing our model, but worked through this problem useing some common sense. All around I'm very satisfied with the results.

The adapter made the cord a bit long but other than that it was great!!!

The video on the GE site was great. Showed step by step instructions on how to remove the old ice maker and install the new one. Also helpful was the detail on the water chute which needed to be moved from the old ice make to the new one. Saved hundreds of dollars by not having to have a repairman do this work for me.

Took out the old, replaced with the new. Needed second person to hold the flash light. That is the secret to get it plugged in and secured.

Ice maker was side mount instead of rear mount as shown in previous insructions. Removed one screw and slide ice maker forward. used flat head screw driver to undo the ice maker plug. The ice maker came right out. Removed old ice maker fill cup and put it on the new ice maker. Slide the new ice maker into place and used the same screw to secure it. Pluged it in and turned on the ice maker. Had new ice in a couple of hours. It comes with a round plug to square plug adapter, new fill cup and fill tube, all of which I didn't use.

Only needed to remove one screw, slide unit out and disconnect the power cord. Theb reverse the above operation to install the replace ice maker unit. Quick and extremely easy....

Followed the video, very simple

i watched the free video and then made the switch my ice screw had 4 bolts instead of three that was the only difference used the screw driver to loosen the straps on the connection plug and that was it easy as pie in about 30 minutes i heard it drop a load of ice it beats filling ice trays all the time thank you partselect for the free video it was the difference in my sucess

Took old part out , put new part in. Was so easy thought we did it wrong. Ice maker working great, have lots of ice now. Thank you. Colleen

Wathched the video and it was done in less than 15 min making ice again no problem

I watched the video from the link that was sent to me with the shipping notice. It was very easy to understand. I had no trouble at all. I'm 75 years old woman, however, and I can fix about anything. Don't be afraid to fix appliances yourself if you feel you have the knowledge.

I'm a housewife in her late 40's. Before ordering the part, I watched your video on how to remove and install the new icemaker. First I unplugged the refrigerator. After a few minutes, I unplugged the icemaker and unscrewed it. I lifted it a bit and removed it. I did not use the icecup that comes with the part. Instead I removed the one from the old part and inserted it to the new one. Then I plugged in the new icemaker, placed it inside so as to match the holes and screwed it in. YES, it was that simple. It took me less than 10 minutes to do this. I saved myself over $100!!