GALLITO General Electric Refrigerator - Instructions

looked up how on you tube and didn't find it just for the part but keep looking and saw how to replace other part that was behind touch pad so was easy from there on :)

Removed mother board and replaced. Working fine now

I am more than 80 yrs, always thought I could fix just about everything--but, this looked complicated. Once I received the new icemaker; took a good look where the screw-holes, etc. were, then removed the "old" one. Took about 20 or 30 minutes, then the "new" one was easily installed.

took 1 screw out and removed ice maker and slid new one in and replace screw and connected power cord

i watched the free video and then made the switch my ice screw had 4 bolts instead of three that was the only difference used the screw driver to loosen the straps on the connection plug and that was it easy as pie in about 30 minutes i heard it drop a load of ice it beats filling ice trays all the time thank you partselect for the free video it was the difference in my sucess

Took old part out , put new part in. Was so easy thought we did it wrong. Ice maker working great, have lots of ice now. Thank you. Colleen

Wathched the video and it was done in less than 15 min making ice again no problem

After what I thought was a thorough troubleshooting of said problem I replaced the Water Valve Assy which was really easy as the video shared, but it did not fix my problem. I had forgotten to pull the water line apart at the coupling below the doors (this was a troubleshooting step in another area). The water not dispensing was due to the line being frozen! Putting all items in a cooler with a couple blocks of ice and leaving the freezer door open for the length of watching a movie, the water was flowing again. Still no ice though. Ice maker vs mother board at the rear of the fridge, Hmmmm. Went with the ice maker, watched video, ole Steve makes the plugs disconnecting look easy, I had to use a flat head screwdriver to open the clips (he doesn't mention that) and I had 4 screws where he had 3. Also he didn't mention about the instructions which gives you 3 options with your unit. I had to re-use my Plastic Stripper Plate along with the Fill Cup and Ice Maker Insert. After completion of installation and about a half hour later, I heard ice fall, Wooohoooo!!! Overall the experience will make me think to utilize PartSelect again when needed. Reasonable prices and decent shipping time. Now the freezer light is out...

Reviewed video which was very helpful. Loosened two philips head screws, lifted up ice maker, unpluged power suppy and reinstalled. One of the easiest replacements ever!!

I rolled out the refrigerator, unplugged the cord and unscrewed the 8 screws to gain access to the main control board. I had to squeeze 4 white hangers to get the unit off. At first I thought you turned them which was a little confusing. Once the mother board was hanging I removed the connections which was easy. I did put the right ones on first and had to take them off because the left side would not reach. Suggestion would be to put the left side connectors on first which I did the second time. I slipped the control board back on the white clips and replaced the panel. I plugged the refrigerator back on and it has been working perfectly for the last two weeks. By doing the repair myself I saved $290. Thank you very much. Also I was impressed that I had the part in my hands two days after it was ordered and the shipping cost was on $7.49. I would definitely use Parts Select again if needed. Thank you again.

Went to GE website and researched the problem for the model, determined that it was 90% sure it was the Ice maker, I ordered it and it arrived the next day, installed it and it began working immediately,

Took out one hex screw, disconnect electric couplings, pulled original ice maker out and found that the water supply line to the ice maker was frozen solid as well as the shute cup. Used hair dryer to thaw out the line and the cup reinstaled old ice maker and it worked fine. Did not have to use the new part at all at this time. Am keeping new part for future use.

Took out the old, replaced with the new. Needed second person to hold the flash light. That is the secret to get it plugged in and secured.

I read the step by step instructions that came with the part. I turned two screws and disconnected the electrical harness and Removed the icemaker. Two other parts from the old icemaker were easily removed without any tools and put on the new icemaker. The new icemaker was put in the same way the old one came out. I reconnected the electrical harness and tightened the old screws. The hardest part of the whole job was reading the directions. They were easy to follow if you take the time to Just read them!

Quite easy. Turn off water supply and turn off ice maker at switch inside freezer. Unscrew the old unit, separate the electrical connection, and pull it out. New unit comes with parts that do not fit my refrigerator, so visually examine the new and old units, reuse any needed parts from the old unit, such as plastic water ramp. Reconnect the electrical connector, and screw it back in. Turn water supply back on and then turn ice maker back on at switch inside freezer. Discard unused parts. Wait up to 24 hours for new ice cubes to be made.