ZIR361NPRCII General Electric Refrigerator - Instructions
Jump to:
Keep searches simple. Use keywords, e.g. "leaking", "pump", "broken" or "fit".
- Customer:
- Thomas from Metairie, LA
- Parts Used:
- WR57X33326
- Difficulty Level:
- Easy
- Total Repair Time:
- 30 - 60 mins
- Tools:
- Nutdriver, Pliers, Wrench set
Water Dispenser Doesn't Work
Watched the video on how to repair this problem. Folowed the simple instructions and it worked. The double outlet water valve worked as it should. When I tested the water dispencer nothing came out of the spiggot on the door but water poured out all over the floor because the 5/16" water line from the replacement valve to the front of the refrigerator was brittle and cracked. I've ordered the part. Moral of the story - if your are replacing this double outlet valve, buy the water line and the union for the dispencer. You'll save yourself time, postage and effort. From the looks of it sooner or later the water line gets "cooked" and breaks/cracks.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Matthew from Houston, TX
- Parts Used:
- WR57X33326
- Difficulty Level:
- Easy
- Total Repair Time:
- 30 - 60 mins
- Tools:
- Nutdriver
Icemaker stopped and leaking
Repair was fairly straight forward once I diagnosed what the problem was by reading other peoples problems and repairs on here. I pulled the fridge out & disconnected the power. I shut off the water supply and disconnected it. I removed the back panel and unscrewed the bracket holding the water valve in place then disconnected the electrical connectors from the solenoids that control the valves. At this point I went on a cleaning binge to remove all dust and crud I could get into my vacuum, which is why it took me longer than others. I know it is important to keep the machinery clean so that it can run efficiently so I did it. At this point I used the hairdryer to melt the frozen inlet to the icemaker from the back of the freezer just enough so I could pull it out and remove the frozen blockage. Reinserted the inlet ensuring it was fully reseated in the opening with the foam seal snugly around it. I reinserted the tubes in their respective valve outlets (each is unique size so they cannot be done wrong), next I reassembled the new solenoid valve by reattaching the electrical connectors (mine are keyed which makes it stupid proof) then screwing its bracket back in place. Next I reconnected the water and plugged in the fridge to check for leaks. No leaks (WHEW!!) replace backplate and put fridge back in cubby. Test water dispenser- GOOD. Turn icemaker back on in "quick ice" mode and wait ~40-45 min first batch is GOOD. 5 hours later with about 6-7 batches of ice, all is well- no leaks everything is functional and I am happy.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- ron from national city, MI
- Parts Used:
- WR57X33326
- Difficulty Level:
- Easy
- Total Repair Time:
- 30 - 60 mins
- Tools:
- Nutdriver, Pliers, Screw drivers
fridge was stored in garage without heat in winter & froze up,should have drained all water.
removed old valve & installed new.wire connectors were a little different so i had to replace one set with smaller ones.turned unit on and also found leak in resevoir bottle.waiting for that part now
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Karen from Portageville, MO
- Parts Used:
- WR57X33326
- Difficulty Level:
- Really Easy
- Total Repair Time:
- 30 - 60 mins
My water dispenser was working very slowly, and the ice maker was not working at all.
I called Parts Express, and explained my problem. The representative, She asked if I was getting water in the tray, and I was not. She said that if I wasn't getting water there, then my problem was probably the Dual Inlet Water Valve. I poured some water directly into the tray, and the ice maker made a tray of ice, and dumped it in less than an hour. So, I then ordered the Dual inlet water Valve. My ice maker is working perfect, and I am getting better water pressure from my water dispenser as well. Thank you for your assistance.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Kenneth from Blairsville, GA
- Parts Used:
- WR57X33326
- Difficulty Level:
- Really Easy
- Total Repair Time:
- 30 - 60 mins
- Tools:
- Nutdriver, Screw drivers, Socket set
Water in Door would not cut off. Solinoid on flap ice shute would not close. Corroded and inoperable.
The video instructions were outstanding in showing how this repair was to be completed. Follow these instructions and Job was very easy. Replaced ice shute flapper and arm, soloinoid and Micro switch for water flow control. Reassemble by reversing procedure. Follow video instructions on how to replace water control valve in back of fridge. Test water flow at bottom front of fridge and defrost flow tube in door if necessary. I used tupperware container with hot water on top of ice shute shelf in fridge door. A couple of times changing and water was flowing. Great site and detailed video instructions for an effective and cost saving self repair. I saved several service trips and service calls and labor costs of a service tect. Parts costs were also a lot cheaper than service tech would have charged. Thanks PartSelect.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Larry from Raymond, NE
- Parts Used:
- WR57X33326
- Difficulty Level:
- A Bit Difficult
- Total Repair Time:
- 1- 2 hours
- Tools:
- Nutdriver, Screw drivers, Wrench set
Water running in freezer compartment
Original equipment valve ran from 2003 to 2010 until a mouse got on top of valve and did a number. Valve purchased in 2010 (installed to solve the same water flow problem occuring in 2012) was installed. I constructed a small tin shield over the valve unit in 2010 to protect the top of the valve from future possible damage. Two years later, the valve failed again - water flowing in freezer. (These Chineese replacement parts should really last longer than two years - I feel they insure future sales by making them poorly) - Both times, the outlet tube above the ice maker was completely iced up and a good deal of time was spent with a hair dryer to melt this ice. (This ice problem can be observed by looking across top of freezer compartment to observe the water outlet area. Turn off water supply and unplug fridge. Four screws were removed to get to the ice maker and then two top screws were removed to pull out ice maker unit (I left hose attached and unit hanging with some support) When installing the double valve, I blew on the loose water tube going up to the ice maker to be sure it was ice free. Taking the old double valve unit out was simple, just remember to press in on the plastic structure around the plastic tubes before pulling out the water tubes. Reattach electrical connections. Press the plastic tubes in as far as they will go for a water tight connection. Reinstall water supply hose and tighten nut. With ice melted, reinstall ice maker with two screws and the front ice maker panel with four screws. Plug in the fridge, turn on the water and you should have ice again as soon as the freezer gets down to 15 degrees.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Dan from Seattle, WA
- Parts Used:
- WR60X30922
- Difficulty Level:
- A Bit Difficult
- Total Repair Time:
- 1- 2 hours
- Tools:
- Nutdriver
broken fan blade
about an hour to figure out what was causing the vibration and noise and about an hour to put it back together and 5 min. to order a new fan blade thank you.It started making noise during thanksgiving dinner so we toke it apart after dinner and I cut the other 2 blade to match the broken one so to cut down on the noise and vibration semi put it back together and 7 days later the part arrived.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- PW from LAS VEGAS, NV
- Parts Used:
- WR57X33326
- Difficulty Level:
- Really Easy
- Total Repair Time:
- 15 - 30 mins
- Tools:
- Nutdriver, Wrench set
No water to ice maker or water dispenser.
Checked to make sure it wasn't a plumbing problem. Then made aide sure the filter wasn't plugged. Then went to Parts Direct's web site. According to their information, the most likely problem was the duel inlet water valve. I followed to video instructions provided on the web site...finished the job in less than 15 minutes...and solved the problem. I will certainly be using your service in the future!
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- James from Sarasota, FL
- Parts Used:
- WR57X33326
- Difficulty Level:
- Really Easy
- Total Repair Time:
- 15 - 30 mins
- Tools:
- Nutdriver, Socket set
refrigerator would not despense water
the old dual inlet water valve was 2 years old and stop despense water. this is not the fist time that i changed the valve so i know when the frigerator is not despense water it s time to change the valve. and its simple shut off water supple to frigertor, pull the electrical plug. remove all the screws from back of back panel, the dual inlet valve is located at the bottom left side remove the inlet water supple line, unscrew the bolt holding the valve in place disconnect the two electrical connection from valve and remove the two water lines(one black and the other white) these two water lines have a push in fitting just push in each line at same time hold in the white collar while pull out the water line. with the new valve install both water lines by pushing them in the black line is larger in diameter that goes into the larger valve connector and the white goes into the smaller diameter connector. then connect to electrical connector these can not be mixed up because the red excepts the larger terminals and the white connects to the smaller connectors. place the dual inlet into a manufacture whole and bolt it back onto the frame of frigertor, connect to water line onto the valve, turn on water supply, check for water leaks. if all looks ok replace back panel, plug in electrical cord. your ready to go.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- CAROLYN from BOWIE, MD
- Parts Used:
- WR57X33326
- Difficulty Level:
- Really Easy
- Total Repair Time:
- 15 - 30 mins
- Tools:
- Socket set
Water valve stopped working
Took out the old and put in the new one...Water is back on!
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Rob from Seneca, SC
- Parts Used:
- WR57X33326
- Difficulty Level:
- Easy
- Total Repair Time:
- 15 - 30 mins
- Tools:
- Nutdriver, Wrench (Adjustable)
No water, ice maker worked
The repair is easy enough, only problem I had was that I ordered the wrong part initially. Unfortunately, on the parts schematic there are two different parts listed and I didn't realize it. I did not look at my water valve prior to ordering, and naturally ordered the wrong one. One good thing, with the wrong part, there is a video showing the repair which I had watched. When I got the right part, the repair was basically the same as the video.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- stephen from Los Angeles, CA
- Parts Used:
- WR57X33326
- Difficulty Level:
- Easy
- Total Repair Time:
- 15 - 30 mins
- Tools:
- Nutdriver, Screw drivers, Wrench set
Diverter valve for water to dispenser and icemaker leaking. We noticed a leak in the basement and tracedto the refrigerator.
This is a cabinet depth fridge which fits snugly into its space in the kitchen. The worst part of any repair is pulling it out into the center of the kitchen and pushing it back in. After that we took off the back cover and the part is at the lower left rear corner of the unit. It was obviously spewing water. We shut off the water to the unit and ordered a new part. When the part came, we pulled the unit back out and disconnected it. The most difficult part was that one of the connections required a half inch open-end wrench to loosen/tighten. The other connections were the pull push quick connect type. The actual repair was very easy. There are other repairs associated with the leak that will not be easy. Damaged wood floor.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- STEVE from Porterville, CA
- Parts Used:
- WR57X33326
- Difficulty Level:
- Easy
- Total Repair Time:
- 15 - 30 mins
- Tools:
- Nutdriver
h2o not flowing to ice maker
First I turned the water supply off to the fridge.Next, I let a little water out from the supply line & into a container in order to rule out a faulty line or valve. Since I was able to get water from that, I figured I had three possibilities left to work on. I already intended on replacing the water filter so other than replacing the entire icemaker I would order the water valve. I ended up spending approximately around $60 for both items but could have saved more $ if I had bought the water filter from you guys. I was familiar due to past experiences involving the water valve but I did read some of the experiences that was printed online and thought that was a plus and because of your self help guidance it enables an average Joe to repair an appliance without being sent to the poor house. Thank you immensely and Look forward to doing my part shopping on line & thru your company. Yours truly, Steve
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- rich from smithtown, NY
- Parts Used:
- WR57X33326
- Difficulty Level:
- Easy
- Total Repair Time:
- 15 - 30 mins
- Tools:
- Screw drivers, Socket set, Wrench set
Water leaking from ice-maker/water line
I first looked at the youtube video on how to replace the part. Then I just followed the step by step instructions
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Bill from Ashland, MS
- Parts Used:
- WR57X33326
- Difficulty Level:
- Easy
- Total Repair Time:
- 15 - 30 mins
- Tools:
- Nutdriver, Wrench (Adjustable)
Ice maker not making ice and leaking water in the door
Watched the video that was already on line and did the job in less trhan 15 minutes. Ice maker now making ice and there is no leak in the door.
Was this instruction helpful to you?
Thank you for voting!