Models > ZIR361NPRCII > Instructions

ZIR361NPRCII General Electric Refrigerator - Instructions

Jump to:

All Instructions for the ZIR361NPRCII
76 - 90 of 185
Keep searches simple. Use keywords, e.g. "leaking", "pump", "broken" or "fit".
Customer:
VICTOR from ARLINGTON, TX
Parts Used:
WR57X33326
Difficulty Level:
Really Easy
Total Repair Time:
Less than 15 mins
Tools:
Nutdriver, Wrench (Adjustable)
outlet water valve leak
I was unplug the electrical,closed the water line.replaced old water outlet with the new one;and there work fine.Thanks
0 of 1 people found this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!
Customer:
susan from hampton, VA
Parts Used:
WR57X33326
Difficulty Level:
Really Easy
Total Repair Time:
Less than 15 mins
Tools:
Nutdriver, Pliers
water continued to leak out of dispenser after use. poor water pressure.
It was as simple as taking off back panel and disconnecting 3 tubes and and two plugs to remove old valve and attaching the new valve piece to the 3 tubes and two plugs! It actually took more time getting the panel off than making the repair AND it saved us a little over $300 as the repairman quoted a price in excess of $350 to repair it. He was actually the one to tell us to buy the part ourselves and repair it. We are thankful being able to get the part and for an honest repairman.
0 of 1 people found this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!
Customer:
Rashedul from Ellicott City, MD
Parts Used:
WR57X33326
Difficulty Level:
Really Easy
Total Repair Time:
Less than 15 mins
Tools:
Nutdriver, Screw drivers, Wrench set
I had no water being dispensed from the door, but had ice!
After confirming that a frozen water line was not my issue, I confidently bought this item and installed it within minutes after receiving it! It is easy to install - just close the connection to your refrigerator, open the rear lower panel, disconnect the water tubings and electrical connectors. Reverse that - you have the installation. Plug the refrigerator back on, turn the water back on for the refrigerator - and observe for any leaks. If no leaks - try dispensing water. Working great for me! My refrigerator's model is a GE, model # zfsb26dnass.
0 of 1 people found this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!
Customer:
Richard from Des Plaines, IL
Parts Used:
WR57X33326
Difficulty Level:
Really Easy
Total Repair Time:
Less than 15 mins
Tools:
Nutdriver, Wrench set
Water flowing from ice maker
PartSelect helped me identify the part, got it in only a few days and I followed the easy to follow video featuring Steve. Awesome!
0 of 1 people found this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!
Customer:
Anthony from McKinney, TX
Parts Used:
WR57X33326
Difficulty Level:
Really Easy
Total Repair Time:
Less than 15 mins
Tools:
Nutdriver
Water would not come out of front of refrig. I maker worked fine.
Removed back panel. Cut the water lines and replaced the double outlet water valve. The only issue was the long period of time until the water flowed from the outlet. Be prepared to wait, it will take some time for the water to flow.
0 of 1 people found this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!
Customer:
Brook from San Antonio, TX
Parts Used:
WR57X33326
Difficulty Level:
Really Easy
Total Repair Time:
15 - 30 mins
Tools:
Screw drivers
water leaking past outlet valve into freezer
1. Remove back cover from frig
2. Remove Double Outlet Water valve from frame
3. Place towel under valve, remove supply line to filter
4. Cut black and clear lines next to valve, ensure a smooth cut
5. Slide new connectors onto lines, press lines into valve firmly, make sure they slide in all the way
6. Slide connectors into valve locking into place
7. Re-connect filter supply line and re-connect valve to frame making sure lines are in the proper place
8. Replace back cover of frig, do not over tighten screws
0 of 1 people found this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!
Customer:
michael from west bend, WI
Parts Used:
WR57X33326
Difficulty Level:
Really Easy
Total Repair Time:
Less than 15 mins
Tools:
Nutdriver, Screw drivers
Unit would make ice, but would not dispense water
Simple repair. I first shut off the water supply to the unit. I then removed back cover from lower part of the unit. The water valve is on the lower left side. I began by removing the screw on the bracket that holds the part in place. This screws into the back of the unit. I then disconnect the water line by unscrewing the fitting. Then unplugged the two electrical connections in the back of the unit. Lastly, remove the two hoses that plug into the bottom of the the unit. The installation was essentially the reverse of the the removal. The whole process took about ten minutes.
0 of 1 people found this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!
Customer:
Peter from Zionsville, IN
Parts Used:
WR57X33326
Difficulty Level:
Really Easy
Total Repair Time:
Less than 15 mins
Tools:
Nutdriver, Wrench (Adjustable)
Ice maker was overflowing.
This repair is EXTREMELY easy to conduct even for the novice. The first step was to shut off the water supply at the wall, and disconnect the power cord to the refrigerator. Remove the six panel screws to remove the lower back panel. On the lower left hand side is the water valve. This is connected by only one screw, so that was removed. Compare your new valve with the one you are removing to double check that the units are the same. Disconnect the inlet water supply line and connect it to the new unit. Disconnect the two water outlet lines from the old unit and connect to the new unit. Finally, disconnect the two power plugs from the old unit and connect to the new unit. These are all colored coded or different sizes, so there is no way to fowl this up! I just recommend disconnecting and reattaching one at a time so that you are doubly assured you are doing this correct. Reattach the valve unit back onto the side of the refrigerator. At this point, I turned on the power and water supply to check for leaks. Also, have someone run the water in the ront panel dispenser to ensure things are working properly. Once that is completed, reinstall the back panel and you are done. I did this project about two weeks ago, and things are working great now. Saved a lot of time and money by doing this job myself.
0 of 1 people found this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!
Customer:
James from Holland, OH
Parts Used:
WR57X33326
Difficulty Level:
Easy
Total Repair Time:
Less than 15 mins
Tools:
Screw drivers, Wrench set
Nurse fixes Refrigerator Water leak back of Fridge
1. Turned off water near hot water tank 2. Removed back (small section) of the refrigerator, only 7-8 screws. 3. Disconnected the old water hose (comes out easily. 4. Reconnected new water valve 5. Turned on water @ hot water tank 6. Replaced back of refrigerator. All done! I have never done anything like this, and I had no instructions, very easy to figure out. The part cost $48 here.
0 of 1 people found this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!
Customer:
Daryl from Scottsdale, AZ
Parts Used:
WR57X33326
Difficulty Level:
Really Easy
Total Repair Time:
Less than 15 mins
Tools:
Nutdriver, Wrench (Adjustable)
pin hole in water valve leaking
turn off water remove back cover remove 1 screw holding water valve use wrench to remove main water line input push up holders on bottom of selinoids pull both output lines loose disconnect two electrical plugs reinstall new valve in reverse order
0 of 1 people found this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!
Customer:
William from Tampa, FL
Parts Used:
WR57X33326
Difficulty Level:
Easy
Total Repair Time:
15 - 30 mins
Tools:
Nutdriver, Screw drivers, Wrench (Adjustable)
Leaking water dispenser
It was very simple. Pull the fridge back (unplug and turn off water), remove the cardboard backing and disconnect/unhook the current water valve and reverse the process to connect the new.
0 of 1 people found this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!
Customer:
jackie from Miramar, FL
Parts Used:
WR57X33326
Difficulty Level:
Easy
Total Repair Time:
15 - 30 mins
Tools:
Nutdriver, Wrench (Adjustable)
water dispenser wouldn't work on occasion/s
per the video - took off panel, remove the existing part, and replaced.
0 of 1 people found this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!
Customer:
Gerald from Colorado Springs, CO
Parts Used:
WR57X33326
Difficulty Level:
Easy
Total Repair Time:
15 - 30 mins
Tools:
Nutdriver, Wrench (Adjustable)
Water leaking on floor from water valve
removed rear cover of Frig, found valve was cracked and leaking water. turned off water and ordered new valve. After receiving new valve, Removal and installation took about 15 minutes. Pretty easy, a no brainer.
0 of 1 people found this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!
Customer:
lewis from hacket, AR
Parts Used:
WR57X33326
Difficulty Level:
Easy
Total Repair Time:
15 - 30 mins
Tools:
Nutdriver, Pliers, Screw drivers
water leaking inside freezer area and freezing everything ice maker wouldnt work
pullee refrigerator out to get to back un pluged power took off back cover unscrewed one screw to loosen water valve unscrew water inlet line ther are two water lines in back of water valve i cut them as close to water valve as i could push the water lines that i cut off into water valve makin sure in the rigfht place they are quick disquinect just push in and ther on screwed water valve back on connected water inlet line replaced back cover pluged in power pushed refrigerator back in and was done it had to run for a little while to get the air out then worked fine
0 of 1 people found this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!
Customer:
Larry from Beavercreek, OH
Parts Used:
WR57X33326
Difficulty Level:
Easy
Total Repair Time:
15 - 30 mins
Tools:
Nutdriver
Ice maker inlet tube slow dripping caused freeze over
Unscrew the mounting screw and cut the tubes as close as you can to the valve. You cannot reuse the valve as the self sealing lock washers will be destroyed once you take out the tubes. Push the newly cut tubes into the new self sealing new valves and remount. Easy Peasy!
0 of 1 people found this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!
All Instructions for the ZIR361NPRCII
76 - 90 of 185