ZIR361NPRCII General Electric Refrigerator - Instructions

Changed out the double outlet valve which was pretty easy, after getting the right one, had the wrong part number for the first valve, not PartSelects fault, but still no water.Before changing valve, ice maker stopped making ice, figured the valve went bad on both points. After changing valve, got ice but still no water.Now what? Pulled the front cover off the freezer door where you get ice and water and found the bracket, } that holds the micro switch that works the water valve broken and the switch dangling. I screwed the switch back to the spacer between it and the frame and glued the spacer to the frame with plastic crazy glue.Got water!

Rolled the fridge away from the wall, unplugged the unit from the wall outlet, and removed the back panel by taking out the 6 1/4" nuts that held it in place. Vacuumed the dirt and dust out, and sneezed viscously for 2 minutes. Removed the 3/16th nut holding the water relay. removed the inlet water line, and quickly replaced it. dried off, then went down stairs and turned off the saddle valve. mopped up the water, then removed the water inlet valve. Removed the 2 water lines to the unit (Ice and water feeds) and removed the 2 wire connectors. reversed the process in installation, except the drying myself off part, and sneezing from the dust and dirt.

-unplugged the refrigerator
-replaced water filter inside refrigerator
-turned off water suppy at valve
-unscrewed tin cover on lower part of refrig
-took brace off that holds the double water valve
-disconnected water lines and caught excess water in a bucket
-pulled out both electrical plugs out of old dual pump
-blew out with air the black water line that runs diagonally from the part to the top of refrig going into ice make(to make sure not clogged)
- Installed the new part and reconnected all of the above.
plugged in the refrigerator
opened the valve to let water flow inot refrigerator.
done--but still no ice cubes? HELP!

Replacing the water valve was easy - the video was excellent. However, the problem was not solved - no water even after replacing the water valve. Anyone have any other thoughts?

It went exactly like the repair video showed. I removed the back cover, unhooked the water lines, unplugged the electric connections, and replaced the valve. That video made it super easy and it is now working like it should.

Followed the instructions from your site and they were perfect. Unfortunatly that wasn't the problem. It still doesn't work.

replaced double outlet water valve. Valve works as it should. Shipping was much quicker than I expected.

1. Remove back cover from frig
2. Remove Double Outlet Water valve from frame
3. Place towel under valve, remove supply line to filter
4. Cut black and clear lines next to valve, ensure a smooth cut
5. Slide new connectors onto lines, press lines into valve firmly, make sure they slide in all the way
6. Slide connectors into valve locking into place
7. Re-connect filter supply line and re-connect valve to frame making sure lines are in the proper place
8. Replace back cover of frig, do not over tighten screws

watched your video,went to work

Unplugged fridge, shut off water supply. Removed bottom back panel of the fridge and carefully vacuumed up all the dust. Located the water valve to the left of the compressor. It is attached to the side of the fridge by a metal bracket. Remove the screw from bracket and lift up on the whole assembly. Now I removed the electrical connectors and pushed in on the quick release tabs to pull out water lines. When installing water lines to new valve be sure to push them all the way in. The water lines are marked so you will know how far they must go in. Attached electrical connectors and remounted whole assembly back to the side of the refrigerator. Turned on water supply and plugged fridge back in. Checked water dispenser for proper operation and also checked water valve for leaks. Reattached the back cover to the fridge and that was it.

1)turn off water supply to appliance 2)disconnect appliance from power supply. 3)remove grill. 4)remove valve retaining fastener. 5)disconnect two wiring devices. 6) depress retaining devise at each water line to disconnect. note: if the lines do not releace, use utility knife to cut lines as close to unit as possible. 7)attach new valve in reverse order.

Shut off water supply and unplugges refrigerator. Took of bottom panel on back of refrigerator. Discontected power plug and water lines from old water valve, removed water valve. Put in new water valve and reconnected water lines and power plug. Plugged refrigerator back in, turned on water supply and checked for leaks. Put cover back on. (It's also a good opportunity to clean out the dust and dirt under the fridge and around the motor and condensor)

Followed instructions others posted. No need to cut any water lines, just push the white collar on the new valve, pull out line and do the same to install lines. Only issue was inlet line leaked after initial installation. It was leaking above the connection, so teflon tape wasn't the answer. Answer was to hold the line in exactly the routing place it was before removing.
It took a few days for ice machine to return to normal (as in making ice in quantity), but works like a champ now.

turn water off to ice maker,unplugged refrigerator, took back panel off took old part off and put new part on

Just put on, part was great. Will buy parts again from this company.