TPJ24PRBABB General Electric Refrigerator - Instructions

My dog ate the plastic portion of the new part before it was installed.

Rolled out the frigerator from the wall. Removed the electrical plug from the wall. Turned off the water valve; disconnected the inlet water line at the frigerator. Detached the dual valve assembly from the frigerator; identified and disconnected the outlet water lines and the four electrical lines from the old valve and installed them on to the new valve. Remounted the dual valve assembly on to the frigerator. Turned on the water and checked for leaks. Re-plugged the electric cord in the wall outlet; pushed the refgrigerator back into position. Total elapsed time was about 15 minutes, not counting the time I directed my wife to get me various tools from my work bench and the time it took me remove my 88 year old body from the kitchen floor, back to an upright position. Peeked into the freezer several times over several hours to be certain there were no leaks.

took off the panel, took out 4 screwws, took out old flap, installed new flap, put screws back in , and put trim back on.

We pulled out our refrigerator and found the leak coming from a valve that controlled the purified water and ice machine. We shut of the water source at our filter system and then removed the part. Looked online and found the part we needed at a great price. Ordered it and installed it when it arrived 3 days later. Easy install and we now have water and ice coming from our refrigerator again- not to mention a clean floor underneath too.

Turned off water, ordered part based on photo and partial appliance model number (my model number was not listed); removed old part using hand wrench and nutdriver: slid existing retaining nuts up waterlines(left on for furture reuse if needed) and slid lines into "Pex" type connectors and remounted (one screw) valve to refrigerator and turned on water.

Note: From Part ordered to received was less than 36 hours!

Turn off water supply line. Use Nut Driver to remove bolt holding assembly to the fridge. Disconnect (2) electrical connectors. Use wrench to disconnect water supply line, (NOTE: Since this unit is a universal type replacement, it did not re-mount to the fridge in the same fashion as the old assembly. I had to play with it to determine how to mount the new assembly in order to align & pick-up the existing bolt hole). Snap on the provided electrical connector adapter prongs and reconnect both connectors. Apply teflon tape on threads of water supply line fitting (optional). Tighten (do not over-tightened) water supply line to assembly (wrench). Use dikes to cut off compression fittings from both the ice and chilled water dispenser lines. Push lines into assembly. Re-mount assembly to fridge. Turn on water supply line. Check for leaks.

It is a dream with less than a minute I unscrew the old part and install the new part

remove old valve, water lines and electrical wires and replace water lines, duel water valve and wires

replace entire inlet valve (block)

remove the 'pop-out " frame around the door recess, you pry the flexable seal from around the ice despenser, have someone hold the unit with the wiring, remove the one screw that holds the door recess, and replace the new one. reverse the procedure. remember to unplug thr frig. first

Un-plugged the refrigerator, removed the existing water valve and pressure fittings; replaced the old tubing and reconnected the faston connectors using the two adaptors provided.

Took about 30 minutes.

Works fine although the sound of filling the ice-tray is a bit lauder that the previous valve.

Placed the glass shelf in the new shelf frame and the frame in the refrigerator.

I was unable to positively identify the replacement shelf frame on the GE web site. Part Select's exploded view made it a piece of cake!

really simple,take 2 nuts loose pull the hose out and then replace.took less than 30 minutes

Shut off water & elect to refg. moved refg out from wall. Removed back cover. disconnected water & electric connections. Removed old valve and installed new one . Plastic tube fit in same place elect pins (4) snapped in place. Used teflon tape when connecting copper plumbing to stop leaks. Also cut old tubing & replaced copper 1/4" compression ring. Note I ordered part before noon on thursday, part arrived fri AM 9:00 FedEx.reg service. cleaned up mess picked up tools. Refg worked like new. saved money on service call. Thanks

I removed the old valve assembly from the refrigerator's cabinet with a nut driver. I then pushed the lines for the water dispenser and ice maker into the valve and attached it to the cabinet. After connecting the water supply we had ice and water.