GSE25METBCWW General Electric Refrigerator - Instructions

Very easy with small screw driver . Carefully pry broken switch out pull off two connectors install new switch connect as before . Unplug refer 1st . Works great . Refrigerator will not work with bad switch

Removed the two screws holding the plastic cover in place and snapped off the cover. Waited for the part only two days and we were done. Easy to snap back together.

Pulled out broken switch with flat head screwdriver and replaced with replacement part purchased from partselect. Easily plugged in new part and replaced.

Took cover off, pushed blade on, and replaced cover

Really easy

Since I'm confined to a wheelchair, my wife had to remove the icemaker which was no problem then with it on the table I was able to install the new stripper arm which was also no problem. The icemaker now works great and thanks to Partselect for their quick delivery and great prices.

Remove all shelves and back duct work in refrigerator section. Remove 4 screws and electric door / blower section. Part was exact replacement. Refrigerator is working perfectly.

Poped whole switch out with flat head screw driver. Removed wires with needle nose players and held the wires so they wouldn't get pulled back inside fridge shell. Attached wires to new part like a plug. Lights ccame back put new switch back inside wall. Shut door

Had to grind down the three middle plastic arms with a small grinder. The arms on the icemaker would hit the plastic arms and break the new one off too if this wasn't done. Perfect fit now.

frig ran to much and pump on to long noticed light switch sticking when door was opened replaced the light switch took care of the problem the switch controlles more than just the light popped out with a screwdriver careful to find the side of it that has the retainer clip on it and the direction of the switch in correct position so it goes off when you close the door flat side facing the back a 2 minute job at most

Used a 2" putty knife to lift off the old switch. Disconnected the broken switch and replaced it with the new one. Took about 1 minute.

Remove ice tray, turn off ice maker lever, then remove what's left of old Stripper Arm. Then align the Stripper Arm tab (one with hole in it on right) with 1/4" long cylindrical metal peg. Holding peg in Stripper Arm hole, guide the left hand side tab into the groove on the Icemaker housing. Make sure the tines of the Stripper Arm are on top of the Icemaker metal body. Assuming you keep the peg in the hole and the left side plastic tab into the groove on the Icemaker body, you should be good to go. Turn Icemaker lever back on, then insert ice tray. You should hear the first batch of ice cubes start to drop within a few minutes. Enjoy!

Removed control panel. Snapped out pretty easily. Removed flapper assembly (4 small screws). Replaced micro switch by prying it away from its holder (unsnaps easily). Disconnected the two wires leading to the micro switch and connected them to the new microswitch and reinstalled switch in reverse order. Cost of switch, approximately $13 including shipping. Saved a ton of money doing it myself.

Unplugged the refrigerator first....then on the inside of the fridge, I popped the temp sensor cover off (upper LH side) and exposed the old sensor. I snipped off the old sensor about 3" down from the end and connected the new sensor (which I trimmed down to about 3" long) with some heat shrink wire nuts/connectors. Let the fridge run for a day or so and confirmed the problem was solved! Oh yeah, there was no way to tell the 2 wires apart (power vs. ground) on the sensor. However there was a manufacturer's stamp on the wires. So note the orientation of the text and mark one of the wires with a sharpie on both the old and new sensor before trimming. This will give you a reference for which wires to connect when adding the new sensor to the old wires.

Temp. Sensor was under an egg shaped cover on the left side wall in the refrigerator. Remove the cover, cut the two wires to the old sensor and remove it. Connect the new sensor to the two wires using butt connectors. Replace cover and done.