GSS22JETBCC General Electric Refrigerator - Instructions

On this fridge, you MUST take out the ice maker. First took out the shelves. Then take out the ice maker. This is done by taking out the four screws on the side that hold the assembly containing the bulb. Then there is one screw that holds that assembly to the icemaker. Do not take out any other screws, this is a mistake I made that cost me a few more hours figuring out how to get the other parts to mount correctly to the assembly containing the bulb. The icemaker should lift right out once the white plus is unplugged from the assembly that holds the light. Then took out the shelf brackets and finally could remove rear panel. Found it all iced up as others have. Took 1.5 hours to manually defrost while using sponges to sop up all the water that would run into the drain if you let it. Was about a gallon of water so using sponges worked well. Heater was open when checked with a meter, but you could tell it was blown by the way it looked. All cloudy. Put things back in reverse order. Had an issue with the icemaker shooting water out and missing the icemaker. Eventually was able to align better. This fridge had also just stopped dispensing water. I think the lines may have been frozen in the back, because one day after defrosting manually, the water dispenser started working again Overall this took about 4 hours. But a few days later, the water dispenser again stopped working. Not sure about that one. I have a valve already that I will try for this issue but somehow I don't think its the valve.

I am a 45 year old woman who is pretty handy but with no prior knowledge about appliance repair. I do have the attitude that if someone else can do it, so can I, which is helpful. I was able to watch a video on this website that showed me exactly how to replace one of the three parts that I replaced. It totally made it easy so that I knew what to do with the wiring. So far, my side by side is working great. I'm the champion! This repair cost me about $75. Who knows how much a repair man would have charged just to look at it.

I pried the switch casing out of the fridge panel with a butterknife, then unplugged the old switch. I plugged in the new one and popped the casing back in. Easy!

Shut off water supply line to refrigerator, place towel or rag under corner of refrigerator where unit is located (to catch spillage when lines are disconnected). Remove back cover with 1/4" nut driver /loosen inlet line compression nut while unit is still attached(easier to loosen now than when unit is floating around loose)/remove unit from fridge then disconnect line and wires. Reverse process to install. Water lines going to water dispenser&icemaker are marked/wire connections are idiot proof. Check for leaks before pushing fridge back to wall. Thats not idiot proof!

I shut off the water at the shut off valve when I discovered the leak. I started checking on the web for a part and I found PartSelect.com and I couldnt believe there price!! I had checked with a local dealer and it was several dollars cheaper here.Back to the repair i remove the vent cover on the back of the unit about 8 screws and then there was on screw holding the water valve and three water lines to lines use the puch in method and one is screwed on , i simply remove those and reinstalled the new valve with the coresponding lines. in a few minutes i had ice and water out the door good as new!! I also took the time to install a new five yr water filter!! actually this water valve is much quieter than the origianl I am well pleased with PartSelect I will do bussiness with them again!! Thanks Bob

1. Removed all food, shelves, and ice bin from freezer compartment.
2. Removed freezer light hood and unscrewed freezer bulb.
3. Removed rear evaporator cover panel (2 Phillip’s screws, 2 hex screws).
4. Melted ice on coils with hair blow dryer (needed bath towels to collected water).
5. Removed old defrost heater (2 Phillips screws, 2 plug-ins).
6. New heater connected without any adjustments.
7. Replaced evaporator cover ice bin, shelves and food.

After removing three screws on the ice bucket, it basicly came apart by itself. I needed to use pliers to remove the old nut because it had over tightened itself onto the shaft. Be careful here - it is a left hand nut - not a normal right hand nut! Reassembly was a snap putting the parts back together in reverse order. Unit has been working great since the repair.

took back panel off in freezer.unpluged unit then cut wire to sensor tie in new one wire nut them up and taped.on the heater strip took off two screws and unpluged two wires put the new in same way as taking old one off.I am pleased that the parts from part select came as fast as they did I would for sure buy from them again and prices were very fair.Thank you very much for your service.

I watched the on live video. Piece of cake!

The repaire guy came in tooke it out and told me it is goin to coast $20 for the part and $50 for the labor..... So I looked, It was soooo eeezzz ALL you have to do is get the switch out( with help of my butter knife :) it plugs in to a little outlet on the wire (on the botom side) so take out the old one and plug in the new one wich I got for $8 + $6 shipping = $15 THANK YOU PART SELECT for saving me $55 Im a 36 y/o stayathome mom and Ihave never don this before, Im very proud of my self. well... it was very easy!

removed 3 screws with 1/4 " nut driver, unplugged 2 plugs by prying out on side tabs, removed bracket and motor. Used vice grips to hold motor shaft and used screwdriver to turn auger fork clockwise and remove. Unplugged two connectors from motor. removed 3 screws with 1/4" nut driver to remove motor. changed rubber boot from old motor to new. Reversed procedures to install new motor on bracket, auger fork, bracket in freezer, etc. Only difficulty getting both hands in narrow freezer compartment. Still didn't work, called repairman. When he got here I showed him the problem and lo and behold, now it would not dispense water. He diagnosed it as a bad motherboard, replaced it and all good now. Motherboard $150, diagnose and labor $90, but it is all good now and I even have a spare motor. The failing mother board causes strange howling noises at times and we discovered the compressor fan had also stopped working and in a short while I would have had a bad problem. Caught it just in time!!!

Removed panel from inside the back of the freezer section, by removing four screws. Then, sprayed the ice build-up on the coils, with hot water until all of the ice was melted away. (Note: be certain to plug the drain hole, and use several towels to catch the water drainage. ) Removed the Defrost Heater Element by removing two holding screws. Unplug the unit and pluged-in the new unit and replaced all screws as originally mounted.

Level of difficulty, as far a mechanical skill goes is relatively easy; however, everything in the interior of the freezer (including icemaker) must be removed to get to the defrost thermostat. The defrost heater only needs the racks and back panel removed. It probably took about 45 minutes with a heat gun to melt the ice off of the coils so that I could work on it-need lots of towels/rags to pick up the water.

First, we called Sears Repair and had a technician come to our home. He stated the motherboard had gone bad probably due to a power surge (we had no surge protector on the appliance). His price for repair was $465.00. We opted to go online for the part and found it for $165.00 through PartSelect.com. It was a very simple procedure of removing the old and installing the new. A few turns with the nut driver to uncover the part, a few tugs with the pliers to disconnect and voila!.. The fridge was back to cooling in no time.

Existing instructions on the site for this repair were very helpful. They just needed a little more detail: "After removing the front cover to the control panel..." Figuring out how to do this took the most time. I finally pried at the bottom with a screwdriver and it snapped out. Next time I'll know to lift at the bottom right and left sides. The existing instructions said to unplug the three connectors. I should have done that; it would have made the job much easier. Instead I let the control panel dangle. That meant I also had to set the ice and water lock to avoid drenching myself. The rest of the job went as the original instructions suggested.