GSS22JETBCC General Electric Refrigerator - Instructions

First I replaced the double valve because the ice maker was not filling with water. It still did not work. Then I replaced the ice maker itself. This worked and was relatively easy to replace. I had to use the water fill "slide" from the old ice maker. The new one was too narrow and it leaked water into the freezer.

I had Sears comre and check it out. They wanted $188. for the part and wanted $211 to put it in. They had the part in the truck. The fridg is a GE Profile and only 2 years old. Told them to forget it. Took me literally less than 10 minutes. They did a diagnostics, cost me $77. they told me the problem. I ordered the part here. It came in 3 days and the directions included were awesome. straight forward. Nice to know there is a place to go to avoid getting the shaft from appliance giants. Thank You !

The details: removed the 3 screws, took a picture of the board, didn't need it, unplugged the 6 plugs. pushed 3 clipds holding the board, unscrewed the ground, removed the board, lined up the 3 clips and snapped the new board in place, replugged the plugs and screwed in the ground. Plug the fridg in, done. Literally that easy.

Part arrived very fast as ordered..need to pry old switch out from top..use care to push the retainer down..after old switch was 1/2 out, I used a putty knife for better leveridge.Remove wire connector...after plugging in the wire connector to the replacement switch, make sure the switch is properly positioned so the switch will depress when door shuts.

Shipping service was great> Ordered on a Friday, received it on Tuesday. Slipped out the old one and put the new one in and it works great

The refrigerator was staying in defrost too long allowing the temperature to rise to the point that part of the ice (probably some of the food too) to melt then re-freeze. I first changed out the temp sensor and thermostat because I wanted to try the cheap stuff first but that didn't fix it, I should have gone with the mainboard first as it was the most likely cause. After putting in the new mainboard in the thing has worked perfectly since. The board was extremely easy to change, take the metal cover off with a nut driver. Carefully unplug the wires from old board and remove the board. The board is mounted on some plastic standoffs that expand after passing through the board, some of these came out while i was disconnecting the wires but some were there to stay until I figured out that I needed to squeeze the top of them to release the board. After getting the old board out just put the new one on the standoffs and connect the wires. Put the cover back on and DONE!

NOTES: The new board had some extra connectors that my old one did not, but the correct connectors were still in the old locations. The instructions that came with the board did talk about making some modifications to the refrigerator wiring on certain models, but that didn't apply to me. If I remember right the models requiring modification were all bottom freezer type. But even if you do have to do this the instrucions looked easy, just cut a couple of wires, no splicing or anything.

Dispencer quit working a year ago, but still still dispenced water. I talked to a service technician about it. He told me the electric motor was froze up, so I orderd a new one. When it arrived I installed it in about 20 minnutes,tried the dispencer and still would not work but this time the water would not dispence eather and this time I noticed the fan quit running and the light went dim when I tried to dispence ice. So I read the customers diagnosis and repares every thing pointed to the main control board, orderd the part and water filter. When they arrived in three days I watched installing this part video and it took me 20 minnutes to install and every thing works fine.

Remove ice holding box. Remove rear plastic cover (nut driver) Unplug two Electrical connectors. Place unit on work bench. Remove 'U' fork, vice grip on shaft and scewdiver as lever on fork (counter clockwise) Remove motor fron plastic Holder. Install new motor & fork. Reverse removal steps. Actually very simple procedure. Usual cost for this typwe of repair is approx. $300.00.

My GE refrigerator emitted high pitch noise a short while ago. I tried different dampening methods that helped but not eliminating the problem. I finally replaced the fan, motor, and associated parts and solved the problem. The total cost was about $50.

I ordered the part on Sunday and had it by Tuesday. It only took a few minutes to install. Basically, I unplugged the unit and removed the cover over the motherboard with a nutdriver. The wires were easy to unplug and reinstall. There was no way to incorrectly install since they could only fit in the correct position. I reinstalled the panel pluged it back in and now the fridge is working great.

First I unplugged the refrigerator, then I had to open up the back of the freezer, use the hair dryer to defrost the ice that had built up in it. Then I unscrewed the screws on both ends of the existing heater unplugged the old heater and plugged in the new one. Then with the sensor, I cut and stripped the 2 wires attached to the old sensor 1 inch away from the sensor. Then I spliced it with the wires on the new sensor, applied wire nut and black tape tightly. Then I put it all back together.

Based on the relatively young age of refrigerator, I suspected the defroster electrical circuit. The evaporator core in the freezer was frozen solid, which confirms that the defrost heater circuit is not working. Thawed out (with a hot air gun) and disassembled the freezer section to access the evaporator core and defrost heater. If you have an ice maker, you will have to remove it to disassemble the freezer section. Confirmed with a voltmeter and ammeter that the defrost heater was not getting voltage. When the defrost heater is working, it will glow with an orange color. Also confirmed with a voltmeter that the defrost timer, located in the refrigerator section was working correctly. You can use a common blade screwdriver to rotate the timer through the cold and defrost cycles. Finally, I determined with a voltmeter and ammeter that the defrost thermostat, located on the evaporator core was not switching the defrost heater voltage. Ordered a new thermostat ($12) from this website and installed it. Refrigerator is as good as new. Be careful, there are many electrical hazards during the troubleshooting phase. Safety first.

Turned off power, removed cover from Ice maker, checked resistance across thermostat for zero (read open), all other switches read proper value (when activated). Ordered and received thermostat. Removed Ice Maker from freezer, removed two screws holding ice tray to Control Assembly. Removed Thermostat and replaced with new one. Applied Silicone Sealant to face of Thermostat for adhesion to ice tray when assembled. Remounted Ice Tray to Control Assembly and remounted in freezer. Works Great...

i used the video it showed on the site or iwould not have been able to do it

Thanks to others who also gave some detailed instruction on repairs I was able to do the same. I have a GE Profile side by side refrigerator/freezer Model No. PSC25PSSCSS The first repair I did was to remove/replace freezer defrost thermostat sensor that is cliped to condenser tube I snipped the wires close to the thermostat and pulled it off the tube I stripped the ends of the wires and twisted the strands then placed a piece of heat shrink tube onto the wire pushing it away from the exposed wire then I soldered the two color coded wires together then I pulled the heat shrink over the conection and used a lighter to heat up the heat shrink until it sealed the conection repeating this on the othr wire as well. I then removed the Old defrost Heater element by removing to screws then I disconected the two wires by simply pulling the connector plugs off both ends of the heater element assembly. This fixed the freezer being too warm for a short time but it started getting warm again that's when I noticed the defrost fan was not working, when you have the door open to freezer push the door switch in you should hear the fan come to life and blow hard. The fan was replaced I had to remove everything to get to it it's pretty simple to do it just unplugs make sure you order the right fan though My fan comes with the Thermistor already integrated into the plug this makes it easier. This fixed the problem with both Freezer & Refrigerator The Temperatures returned to normal Freezer 0 degrees Refrigerator 37 degrees I also checked out the refrigerator side Condenser I noticed only that the Condensate pan was starting to rust so I will remove it and use some Muretic acid to clean it up and then spray it with some Cold Gavanize with Zinc you can get this spray paint at Home Depot it seals and prevents rust. Or you can order a new one for about $ 16 bucks but it will start rusting just like the old one did eventually if you do order a new Condensate Pan I suggest spraying it before you reinstall it so that it will not rust. Greg H. Eldorado, AR

Unplugged the refrigerator and removed inside back panel from the freezer compartment and left doors open to allow all ice to thaw. I chose not to use a hair dryer and speed up the process as this could possibly cause more damage if not done with caution. After all ice was melted i took both screws from heat element assembly and followed the simple instructions that came with the new part. Since meters an i dont really work well together and since defrost thermostat and temp sensor were so inexpensive. I opted to purchase those as well in my initial order. They were as simple to replace as a lightbulb. Unscrew the wire nuts from existing sensors and screw wire nuts back on to the new sensors. Buy purchasing all three items at once i felt it just ensured the fiz was complete and the unit has been operating for 7 days like new. One thing i would pass on. If it is the heating element that is burned out, the glass tuve on mine was very black and charred looking. Also when you take it out of the assembly the element was actually in two pieces. Did something cause the element to stay on until it burned out or just old age i dont know. Again, for less than 20 bucks i purchased the additional parts that would seem most obvious to replace and i would recommebd the same. Part select saved us a lot of money not only in parts but in allowing someone with no considerable knowledge in this areato make repairs without hiring an expensive repairman.