PFCF1NJWC General Electric Refrigerator - Instructions

changed outlet valve.not the problem.needed a new filter valve assembly.

had to remove ice maker and several panels to get to the fan. wires for fan encapsulated so had to cut old and new wires then solder them together while working inside the small freezer area. not too bad all in all took about an hour to get it done. no more wind thru the trees noise and is working fine

Unplugged refrigerator. Unscrewed back cover. Unscrewed dual water valve. Unplugged electrical connections 9red and yellow) . Shut off water valve from wall to refrigerator. Cut black tube (ice maker, cut translucent tube (water line). Connected new valve to water supply. Reconnected black and translucent tubes to new valve. Reconnected yellow and red electrical plugs. Turned on water supply plugged refrigerator back in.

Diagnosis: I removed the nuts holding on the panel at the back of the refrigerator and saw water leaking from the water valve.

Repair: I guided my 10 year old daughter through the actual replacement.

Using a nut driver, unscrew the single nut holding the value to the frame of the refigerator.

Push up the rings around each water tube to release the tubes from the value. Using a wrench, unscrew the supply line.

Put dab of plumbers teflon on the threads.

Reverse all the above:
Screw in supply line, tighten with wrench.
Push water lines for icemaker and chilled water into value assembly.
Position valve and screw in het nut that attaches it to the frame.
Replace rear cover plate and screw in the hex nuts.

Had the wife shut the water off, while I was on vacation. Came home pulled the refrigerator out. Had an issue earlier in the year with a leaking hose. Discovered the valve had many pin holes and was going to need to be replaced. Went on line to Partselect ordered on Saturday. It was easy to determine if I had the right part. Purchased and received on the following Tuesday. 30 minuted later the refrigerator was back up and running with ice and cold water. Have used Partselect before always a great experience

Easy job except for moving the Refigerator but it is on rollers but it is still heavy. Unplug the Ref and shut off the water and replace the valve and the reverse the order. Simple

shut off water supply behind refrigerator, opend line at double outlet water valve. had water there. opend line at bottom of freezer door. no water there when I pushed watervalve on door. replaced double outlet water valve. then had water at hose at bottom of freezer door. but no water at outlet. took hair dryer and heated freezer door until ice melted in hose . then everything worked fine.

Unplugged the unit and turned off the water line to the refrigerator. Removed the six screws holding the back cover. Removed the screw holding the outlet water valve. Unplugged both electrical connectors. Unscrewed the water supply line and cut the ice maker and fresh water outlet lines from the valve. inserted the fresh water and ice maker lines into the correct valve and connected the supply line to the inlet. Connected the electrical lines and remounted the Valve. Turned the water on and checked for leaks. Remounted the Valve and installed the back cover. Plugged the fridge in and ran the front fill until water came out (1:00 minute). Cleaned up and pushed unit back into cabinet.

I couldn’t repair the problem because the part that came did not have the clips to crimp on the end that go into the modular connection,

took a little more effort than the video show to remove old module and replace new. Works fine now.

Unplugged the freezer. Then I gained access to the fan: remove the top freezer rack, remove the ice tray, remove the air flow manifold(needed to unscrew some screws), remove the manifold over the fan and cooling element. I unscrewed the fan mounting bracket. The fan motor's wires are plumbed through some plastic that i would have had to remove, so I decided instead to cut the wires and splice in the new fan motor. Then I put everything back together - the new motor works fine and doesn't make the whining noise.

It was way to ez to install only a couple of minutes that's it

I found that the valve was not the problem. Check to make sure you do not have a frozen water line as I did.

Took cover off, pushed blade on, and replaced cover

Of course I had to order the filter and upon receiving it I installed the new one in about a couple of minutes. Even though my fridge doesn’t have a water dispenser it does make ice. Removed all the old ice from tray and disposed of it cause it was getting a bad taste to it. I let the tray fill up with ice once and disposed of the ice. After it filled up a second time I tasted the ice and had a very good clean taste. And my lesson is I need to replace filter at least once a year I think would be sufficient. That’s all there is to it, simple !!!