GTS22JBPC General Electric Refrigerator - Instructions

removed drawer, unscrewed old slide, screwed on new slide, voila! finished! I was very pleased with PartSelect -- ordering was easy, the correct part came quickly, and packaged very well. All of life should work so smoothly!

I removed the old broken part and replaced with the new part. Simple as pie, my husband was so happy and impressed I had it done by the time he got home from work!!!!

A very simple repair that took less than 10 minutes. About 5 of that was getting a screw driver and putting it back in the tool box. Simply remove the drawer, unscrew the two screws. Install new rail using the same two screws.

What I liked the best about PartsSelect.com was, I ordered the wrong part mistake. When I called to inquire about the refund/return of the un-used part, they were very polite and curtious. She said the return info would be in my e-mail in a minute. She even asked if I wanted her to order the correct part right then. I didnt have the model number with me at the time or I would have. A minute later I check my e-mail and there was the needed info. Excellent cutomer service PartsSelect. All my future orders, I'll check your site first.
Thanks,
Glen.

While only 4 yrs old, an annoying sliding vegetable drawer would tilt to one side and NOT close well at all. After seeing the parts so easily on Parts Select...I had it fixed in under 7 minutes and it is as good as new....you can slide it without frustration

So easy - unscrewed old screws, replaced part, put screws back in!

The hubby couldn't believe that I finished as quickly as I did...

removed two screws which let me take the old part off. I then put the new part on.

Shipping was extremely fast.

Un Plugged the frig. Unlocked the socket by pressing down on the latch. Pulled the socket out ensuring I had enough slack. Unplugged the old socket installed the new. Plugged the frig back in. Tested the switch . Very easy-to-use.

I removed the drawers, then removed the two screws that held the drawer slide in place. I replaced the drawer slide, secured with two screws, and then replaced the drawers.

On the internet forum I read that if the control board needs to be changed , do the same for the Run Capacitor/relay.
The Ge profile refrigerator was 15 years old. First I disconnect the power cord,
I removed the control board at the back of the fridge, replaced it with a new one and did the same for the run capacitor.
Plugged the power cord back and it works fine. GE repair service did not want to come to do it. DIY is fine.

Part received quickly and was a very good deal!

The broken slide rail mounting was held with 2 screws. I removed the plastic shelf on the top and unscrewed the broken part. I replaced it with the new slide rail part and screwed in the 2 screws. I replaced the slide drawer and the top shelf and the job was done...... very easy! Very satisfied!

pluged the wire harness into the new socket from the back and snaped the socket in place.

Remove the drawer and the shelf glass assembly. using a #2 phillips screwdriver remove the two screws that hold the drawer slide rail. Discard the old slide and place the new slide in position and install the two screws. Be careful not to over-tighten the screws. Place the drawer back on the slide and close it. Next place the front of the glass shelf under the lip on the front of the slide rail and set it in place. Job Complete!

I thought I'd be nice and surprise my boyfriend by cleaning his frig for him. In doing so I broke the little plastic rail. I felt bad because the frig is not that old. I asked him where the owner's manual was, and he had no idea. Typical male. So I got on line on the GE website and tried to look up the part number, but they didn't have a diagram of the inside of the frig. I went to your website, found the part in minutes, ordered it, and amazingly it came in just two days. It sat on the dining room table waiting for him to fix it for 4 days. I finally got sick of looking at it on the table so that morning while he was still sleeping I grabbed my handy little cordless screwdriver, unscrewed the screws, slipped the new rail in, and screwed it in. It took less than 5 minutes. He got up later in the morning and asked me where I put the rail and glass top. I said "Where it belongs!" He was shocked.

We went for months not knowing where to get the part we needed until my husband found your site on line. The first part we received was wrong, but with the help of your operators, we then received the correct part. It was only a matter of removing two screws, placing the slide and then putting the 2 screws back in. It was a snap.

Piece of cake - just unscrew the screws and put the new piece on, replace the glass top and replace the drawer. No brainer. Don't ever pay someone to do it.