HTS22GBPW General Electric Refrigerator - Instructions

removed two screws which let me take the old part off. I then put the new part on.

Shipping was extremely fast.

Un Plugged the frig. Unlocked the socket by pressing down on the latch. Pulled the socket out ensuring I had enough slack. Unplugged the old socket installed the new. Plugged the frig back in. Tested the switch . Very easy-to-use.

While only 4 yrs old, an annoying sliding vegetable drawer would tilt to one side and NOT close well at all. After seeing the parts so easily on Parts Select...I had it fixed in under 7 minutes and it is as good as new....you can slide it without frustration

So easy - unscrewed old screws, replaced part, put screws back in!

The hubby couldn't believe that I finished as quickly as I did...

first removed two srews removed rear panel hair dryer to melt ice (took 30 minutes) cut two wires to thermostat spliced onto new part clipped it onto tube -done replace rear panel and 2 screws. very easy job after reading other letters and their experience -saved myself $500.00

On the internet forum I read that if the control board needs to be changed , do the same for the Run Capacitor/relay.
The Ge profile refrigerator was 15 years old. First I disconnect the power cord,
I removed the control board at the back of the fridge, replaced it with a new one and did the same for the run capacitor.
Plugged the power cord back and it works fine. GE repair service did not want to come to do it. DIY is fine.

Find online diagram of freezer section for reference. Disconnect power, remove evap cover plate (214) by removing one of the drawer guide rails.

As evidence of your problem, you might see a giant block of ice built up around the coil. Let this defrost this before continuing.

Find THERMOSTAT DEFROST (24) sensor and clip connecting wires. Match replacement sensor wires by color. Twist and solder wires; or wire-nuts and twisting alone might be okay. If not soldering, seal the wire-nuts connections from moister with a good sizeable piece of duct tape. Make sure your wires are out of the way and not left dangling on the evap heater coil, where they could melt.

Suggest concurrent replacement of evap fan motor if this has not already been done in the past.. This become noisy with age and damage from the ice build up seems to have made mine worse.

Part received quickly and was a very good deal!

The broken slide rail mounting was held with 2 screws. I removed the plastic shelf on the top and unscrewed the broken part. I replaced it with the new slide rail part and screwed in the 2 screws. I replaced the slide drawer and the top shelf and the job was done...... very easy! Very satisfied!

Remove the drawer and the shelf glass assembly. using a #2 phillips screwdriver remove the two screws that hold the drawer slide rail. Discard the old slide and place the new slide in position and install the two screws. Be careful not to over-tighten the screws. Place the drawer back on the slide and close it. Next place the front of the glass shelf under the lip on the front of the slide rail and set it in place. Job Complete!

pluged the wire harness into the new socket from the back and snaped the socket in place.

Frig parts had been scavenged in an apartment complex. Restoring socket was only a matter of plugging in two spade contacts and clipping in socket.

I just took the broken one and replace it with the new one that I ordered. very easy. Thank you!

We went for months not knowing where to get the part we needed until my husband found your site on line. The first part we received was wrong, but with the help of your operators, we then received the correct part. It was only a matter of removing two screws, placing the slide and then putting the 2 screws back in. It was a snap.

Piece of cake - just unscrew the screws and put the new piece on, replace the glass top and replace the drawer. No brainer. Don't ever pay someone to do it.

Removed the old part using a phillips screw driver, cleaned the area, screwed in the new part, replaced the drawer. It was very easy to do, didn't even have to call my husband.