Models > RY4951 > Instructions

RY4951 (RY4951000W0) Gaggenau Refrigerator - Instructions

Jump to:

All Instructions for the RY4951
121 - 135 of 365
Keep searches simple. Use keywords, e.g. "leaking", "pump", "broken" or "fit".
Customer:
HARRY from FSTRVL TRVOSE, PA
Parts Used:
W11396033
Difficulty Level:
Really Easy
Total Repair Time:
Less than 15 mins
Freezer drawer light switch failure.
Disconnect plug from wall. Insert putty knife between light switch.and trim panel , apply pressure to depress plastic spring holding switch in place. Apply a slight twist too putty knife releasing switch from trim piece. This wil expose plug connected to switch. Disconnect plug from switch. Connect new switch to plug. Insert switch into trim. Plug refrigerator into wall socket.
2 of 3 people found this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!
Customer:
Steve from Warner Robins, GA
Parts Used:
W10827015
Difficulty Level:
A Bit Difficult
Total Repair Time:
Less than 15 mins
measure! measure! measure!
With 2 babies and a chaotic household, i failed to double-check the measurements before I ordered the part. No fault of partselect, just user error ;-) I had to return the part bc i ordered the wrong size. Lesson learned, take my time and make sure it's done right the first time. The part fit in perfectly.
I used the search feature on the left side of the website to find the part, since the deli drawer wasn't in the parts diagrams given. The second time, customer service helped me find the part since the correct part wasn't on the website initially.
The deli drawer for this model is in the perfect place to have something dropped on it time and time again. I'm surprised you don't get more requests for this part to be replaced. It's bad design for Maytag to make it out of thin plastic.
Anyway, thanks so much for your patience in dealing with this frenzied mom! :-)
2 of 3 people found this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!
Customer:
John from LEAWOOD, KS
Parts Used:
WP67002659
Difficulty Level:
Very Easy
Total Repair Time:
Less than 15 mins
Tools:
Screw drivers
transfer white border on old drawer to new drawer
with screw driver, pry up white upper drawer border and cover carefully. Place over new drawer in same location on a hard surface. press the upper border over the new drawer and press downward.carefully until it snaps in place. insert drawer in old drawer location.
1 person found this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!
Customer:
MARY A from PITTSBURGH, PA
Parts Used:
WP67002321
Difficulty Level:
Very Easy
Total Repair Time:
Less than 15 mins
"Gourmet Bay" had only one divider. Contents were getting feisty..
Opened package. Washed divider. Dropped in place (where indicated by marks) in drawer. Took a nap.
1 person found this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!
Customer:
Susan from Edgerton, KS
Parts Used:
WP67001255
Difficulty Level:
Really Easy
Total Repair Time:
Less than 15 mins
Ice maker bucket missing
Needed ice maker bucket for extra fridge. Part came the next day, and worked perfectly.
1 person found this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!
Customer:
Marybeth from VACAVILLE, CA
Parts Used:
W11395888
Difficulty Level:
Very Easy
Total Repair Time:
Less than 15 mins
Lost cap for filter
Bought new cap.
1 person found this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!
Customer:
Daniel from SAINT ALBANS, VT
Parts Used:
WPA3223101
Difficulty Level:
Really Easy
Total Repair Time:
Less than 15 mins
Tools:
Pliers, Socket set
Water line feeding ice maker was not producing ice
Take out the elbow fill tube and check to see if ice build up inside tube. Clean tube of ice build up. Replace tube back in. In my case that corrected my problem.
1 person found this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!
Customer:
Carlton from CHICAGO, IL
Parts Used:
W11396033
Difficulty Level:
Really Easy
Total Repair Time:
Less than 15 mins
Tools:
Screw drivers
Light out.
Popped out the old switch and replaced it with the one dying
1 person found this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!
Customer:
Richard from PORT JERVIS, NY
Parts Used:
W11396033
Difficulty Level:
Very Easy
Total Repair Time:
Less than 15 mins
No problems
Just plugged it in
1 person found this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!
Customer:
Linda from NAPLES, FL
Parts Used:
W10830189
Difficulty Level:
Really Easy
Total Repair Time:
Less than 15 mins
Refrigerator Door Gasket Torn
Following the excellent video on Parts Select, we soaked the new gasket in warm water in the bath tub to make it pliable, then simply pushed it into the grooves on the door.
1 person found this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!
Customer:
Royal from RICHMOND, VA
Parts Used:
WP67004028
Difficulty Level:
Very Easy
Total Repair Time:
15 - 30 mins
Tools:
Pliers
New Ice maker was install but technician failed to transfer arm off old ice maker and put on new one..
Work was done by service tech. I ordered the arm for my mom to save time when tech came back to do the job correctly.
2 of 4 people found this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!
Customer:
John from AUBURN, CA
Parts Used:
W11396033
Difficulty Level:
A Bit Difficult
Total Repair Time:
15 - 30 mins
Tools:
Pliers, Screw drivers
Refer lights not working, there are two lights and neither worked. Decided the switch was the problem.
The switch fix but did not fix the problem. I assumed the wires go on the same way as on the old switch. Is it possible if one light Burns out, the other will not work either?
1 person found this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!
Customer:
Chris from Brentwood, TN
Parts Used:
W10823511
Difficulty Level:
Easy
Total Repair Time:
15 - 30 mins
Tools:
Pliers, Screw drivers
Broken Water Nozzle at Door
(1) Ordered PS371704 from PartSelect! Best advice EVER! (2) Unplugged refrigerator (since the water solenoid on the back of the refrigerator is powered to switch ON the water, you NEVER have to turn off the water!) (3) Pull off the refrigerator's bottom grill. (4) With a small saucer under the fittings, unscrew the black and white tube fitting. There is only one nut to remove on the white tubing side. You'll need to undo the compression fitting on the black tubing and slide off the compression nut. You'll need to MAKE SURE you keep these nuts and replace onto the black and white tubing the SAME WAY you took them off. You'll NOT need to use nut drivers as finger tight is the key. Too hard and you'll ruin these plastic nuts. You should get only about 1/8 cup or less of water during this whole exercise. (5) Cut off the old, broken water nozzle. (4) Find a screw of the appropriate size to fit tightly 1/2 way inside the new tubing (this is to ensure your old and new tubing are connected to feed through the door). If screw is not tight within the tubing, wrap part of a plastic (thin) sack around this screw a couple of times and force into the tubing. You'll, of course, then need to use the hacksaw to cut the head off the screw as you'll be forcing the other half of the screw into the old cut tubing (6) Chase the dog out of the kitchen and cajole your wife (significant other) to push the newly joined tubes through the top of the dispenser, through the door and out the bottom as you will be gently PULLING on this old tubing from the bottom until the new tubing pops through the doors bottom. (7) Once this new tubing is out, you will separate the old tubing and, using the nuts in the proper sequence, connect this new tubing to the white tubing. (8) Plug the refrigerator back in and test flow the water. Check to ensure the plastic nuts have no leakage ... button up the bottom grill ... and enjoy the fresh water! PS> Don't forget to praise the wife (significant other) and give the dog a treat for staying out of your face!!
1 person found this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!
Customer:
Mary L. from Millsboro,, DE
Parts Used:
WP627843
Difficulty Level:
Really Easy
Total Repair Time:
Less than 15 mins
Tools:
Screw drivers
Ice maker ejector arm broke into.
Removed old ejector arm and installed new part.
16 of 46 people found this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!
Customer:
MaryAnne from arroyo grande, CA
Parts Used:
W10830189
Difficulty Level:
Very Easy
Total Repair Time:
15 - 30 mins
Replace worn door gaskets
Viewed easy online instruction video. Laid gaskets on flat surface and warmed with hair dryer until they were smooth and unwrinkled. Starting at the top I pulled off the old gasket and beginning at the top I snapped in the new gasket. Carefully smooth as you go. I'm a 72 year old women and if I can do it, you can do it!
1 person found this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!
All Instructions for the RY4951
121 - 135 of 365