XRSS264BB-PXRSS264BB0 Amana Refrigerator - Instructions
Jump to:
Keep searches simple. Use keywords, e.g. "leaking", "pump", "broken" or "fit".
- Customer:
- phyllis from PT PLEASANT, NJ
- Parts Used:
- WP67001503
- Difficulty Level:
- Very Easy
- Total Repair Time:
- Less than 15 mins
Crisper drawer rails had broken
Easy Peasy. Just put in new drawer.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Dean from STEWARTVILLE, MN
- Parts Used:
- WP67002052
- Difficulty Level:
- Really Easy
- Total Repair Time:
- 15 - 30 mins
- Tools:
- Nutdriver
Wheel broken
Took auger apart laid out sequence as removed parts replace the same way . Parts have to go back like they were removed.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Harry from TUCSON, AZ
- Parts Used:
- WP12665101
- Difficulty Level:
- Very Easy
- Total Repair Time:
- Less than 15 mins
Frost and ice was building up on the top of the ice chute inside the freezer
There is a plastic flapper valve that is spring-loaded in the closed position that prevents ambient room air from entering the freezer compartment via the ice chute. The Ice Chute Seal is a simple flexible (rubber-like) disk that just slips over the circular flapper valve. With the freezer door open one can see the flapper valve down the ice chute and one can reach it easily from the outside of the freezer as well. The Ice Chute Seal has 3 notches that make it very easy to remove the old seal and replace it with the new seal. This can be done by feel. I removed the old seal by pushing the flapper valve open with one hand (from the inside of the freezer door) and could then peel off the seal surrounding the flapper valve with the other hand. Once the old seal was removed I slipped the new seal around the flapper valve. No tools required, no screws needed to be removed. The problem I had with frost/ice build-up was solved; there is no more ice/frost build-up inside the freezer near the top of the ice chute. The old seal LOOKED OK but was obviously a bit too stiff to seal the opening against the warm, moist, ambient room air. I was most happy to see that this solved the problem and that it was so easy to do (really less than a minute or two!).
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- WESLEY from INDIO, CA
- Parts Used:
- WP67005959, WP12740302
- Difficulty Level:
- Really Easy
- Total Repair Time:
- 30 - 60 mins
ice bucket And crusher repared
bought new
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- john from TITUSVILLE, FL
- Parts Used:
- WP12665101
- Difficulty Level:
- Really Easy
- Total Repair Time:
- 30 - 60 mins
seal leaking
pull open seal lift up release bottem catch push in to release top catch clean disk and installnew seal put back in the reverse of taking out dont take any thing else apart
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Michael from Sandy, UT
- Parts Used:
- R0181181
- Difficulty Level:
- A Bit Difficult
- Total Repair Time:
- 30 - 60 mins
- Tools:
- Nutdriver, Screw drivers
Replaced dorr closure cam on both doors of side-by-side
The fridge door was easy. Just unscrew top and lift off hindge. The freezer door took longer. But I had the user guide which helped. We unhooked the power harness at the top of the door, and disconnected the water line at the bottom of the door.
Frankly, it wasn't that hard for me because I had my son-in-law do it!
Frankly, it wasn't that hard for me because I had my son-in-law do it!
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Leonard from Reynoldsburg, OH
- Parts Used:
- WPD7749401
- Difficulty Level:
- Really Easy
- Total Repair Time:
- 15 - 30 mins
- Tools:
- Nutdriver
Ice Maker Auger Wouldn't Turn
I removed the ice tray and removed the front plastic cover that simply snapped off. I removed 4 hex screws with 1/4" nut driver. Then pulled the auger forward. This allowed me to slide the end cap into place. I put the auger in place and retightened the 4 hex screws, snapped on the plastic cover it worked fine
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Gregory from Lemon Grove, CA
- Parts Used:
- WP67002052
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Nutdriver
The wheel broke in half.
Remove ice tray from freeze. Removed all screws, replaced wheel. Reassembled unit.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Ricky from Stockbridge, GA
- Parts Used:
- WP67005959, WPD7749401
- Difficulty Level:
- Really Easy
- Total Repair Time:
- 15 - 30 mins
- Tools:
- Screw drivers, Socket set
ice tray was broken
Removed all parts in ice bucket and replaced end cap and bucket.It was very easy and is working great. Thanks for your help
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Jon from Antioch, CA
- Parts Used:
- WP67001503
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
Slide lips on crisper drawer were breaking off
Pulled out the broken crisper drawer and inserted the new one! Thanks so much for your rapid turn-around on my order. My wife was impressed at how quickly I resolved the issue. I'm definitely keeping your website in my favorites list.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- michael from pleasant grove, UT
- Parts Used:
- WP67002052
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Nutdriver, Screw drivers
crushed ice wheel broken
very easy, with use of screwdriver and 1/4 in nut driver. just remember the way the blades go and get them back the same way. had it fixed in 15 mins.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Bob from Oakland, MD
- Parts Used:
- WPD7749401
- Difficulty Level:
- Easy
- Total Repair Time:
- 15 - 30 mins
- Tools:
- Nutdriver
broken end cap on ice icemaker bin
remove the tray from the freezer. unsnap the front cover from the bin. remove the four screws holding the metal helix and grinder assembly to the bin. slide the metal helix and grinder assembly out. slide the new end cap onto the end of the helix. (this is the only tricky part and takes some patience. The stub end of the helix has to slide into the hole in the end cap. You can't bend the helix, just work the end cap around until it slides over the helix end stub). Reassemble the grinder and helix to the bin, snap the cover on and slide back into the freezer.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Sherry from Terrell, TX
- Parts Used:
- WP12740302
- Difficulty Level:
- Easy
- Total Repair Time:
- 15 - 30 mins
- Tools:
- Nutdriver
Arm to distribute ice quit working
removed the old part and replaced with new. Part came very quickly....
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Bruce from Cape Coral, FL
- Parts Used:
- WP12562701
- Difficulty Level:
- Easy
- Total Repair Time:
- Less than 15 mins
broken ice at the door trap door
The ice to the door has not worked for the last 2 years. My wife complained about not having crushed ice to drink with. We looked at buying a new refrigerator. I went back online to look for the broken part again (I have looked in the past but never found the part). I stumbled on this website and found the part and it was only $4.00 and change. Only needed 10 minutes and my hands to snap the part in place. I do need a new ice bucket but it works for now and my wife is happy.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Jesse from Slidell, LA
- Parts Used:
- WPD7749401
- Difficulty Level:
- Easy
- Total Repair Time:
- Less than 15 mins
not distributing ice
1. Removed ice maker from frig.
2. Emptied all ice cubes.
3. Let it warm up to room temperature.
4. Removed front cover from bottom up (unsnapped).
5. Removed 4 screws.
6. Removed old helix cap.
7. Installed new helix cap.
8. Reverse of step 5 to step 1 above.
2. Emptied all ice cubes.
3. Let it warm up to room temperature.
4. Removed front cover from bottom up (unsnapped).
5. Removed 4 screws.
6. Removed old helix cap.
7. Installed new helix cap.
8. Reverse of step 5 to step 1 above.
Was this instruction helpful to you?
Thank you for voting!