ASD2325KEB Amana Refrigerator - Instructions

I removed the two screws on the Ice dispenser housing and dropped it down. I catalogued all the electrical connections on a piece of paper for reassembly and basically followed my nose. I gave my wife the honor of testing it and I held my breath. Replacing this part was a breeze and it functioned perfectly when the job was completed. I wish I had done this three years ago when it failed! Thanks very much !!

First of all I want to thank Michael from Carlisle,PA and this site for publishing Michael's info on the wiring specifics on the new 3 connector Start Relay ( WP2262185 ). The original relay only has 2 connectors The 2 orange wires which are combined to one female connector need to be clipped and separated each to its own connector. Refer to Michael's blog as to which wire goes to which connector on the Start Relay. I replaced the Run Capacitor, Start Relay and Overload just to be safe. The Start Relay was the actual culprit.Thank you for an excellent website!

I had to order three times before I got the right part. This was due to my rush to fix the problem and not studing the diagram carefully (black and white diagrams are not that clear). The repair was very simple. Just remove the rubber from the plastic door and slip on the new one.

Very easy to order from parts select. Took seconds to replace.

Popped out with butter knife and unplugged 3 prong connector and reversed with anew switch.

But, unfortunately it got broken again exactly same way as before.
So, I ordered same switch again for 2nd time.

Maytag should recall that Rocker Switch and build with better materials.

Remove 1 screw under ice maker. Gently pull downwards to unhook ice maker. Disconnected 4 pin wire connector. Remove and set aside the cover and wire loop you will need on new ice maker. Reverse the steps to install new maker. Once new ice maker is installed you will have to wait 2-4 hours for ice. There is a thermostat that will need to reach 10 degrees F to operate.

Problem led to 3 possible problem parts, defrost thermostat, defrost heater or defrost control board. Defrost heater ohmed out to 31 ohms, so seemed good. Defrost thermostat was open when warm but was open after running refrigerator to get freezer side cold enough for thermostat to close, it did not I thought. So I ordered thermostat. Once part came in, I cut up a couple inches on orange and brown wires, stripped off enough to work with. I soldered new one in and heat shrunk the wires. I turned on and it seem to work and all night. Working fine right now.

First I checked to see if the water pump in the base of the refrigerator was working properly. To do this, I removed the water filter, placed the by-pass cap on the water filter head, and dispensed water. The dispenser worked very well so I knew it was not the pump. I had just bought a new filter so it was okay too. So I figured it was the Water Filter Head assembly. To install, I followed previous advice on Part Select website and followed a YouTube video that was excellent (enter "Refrigerator Water Filter Head and Tube Assembly-How to replace). Best advice...Styrofoam block that inserts from back of refrigerator where tubing enters...when removing, push it out from the inside of the refrigerator to avoid breaking it into pieces. Other good advice, unplug refrigerator and turn off valve to icemaker and water dispenser. Easy repair, could do it in half the time now because I was very careful when installing this item. Results: Excellent flow from dispenser!!! And better ice cubes too! Well worth the effort.

Unplugged refrigerator.
Removed water drip tray.
Removed two Phillips screws.
used putty knife to
get behind outer plate and popped it off.
Disconnected electrical connections.
Removed the 4 nut driver screws.
removed ice maker door.
Removed seal around old Ice shoot flap and cleaned.
Removed insulator pad from old ice maker flap and cleaned.
Installed seal and insulator pad on the new chute door.
clipped new chute door intact with seal and pad in place and snapped the top clips into place.

Reversed procedure to reinstall refrigerator parts.

Plugged in refrigerator and tested. Had no issues.

Replaced the relay and capacitor it runs.

I changed the bulb but it still didn’t work. I ordered a bulb holder and replaced it and it works properly now. It was an easy repair, remove the bulb, gently pry the bulb holder out with a screwdriver and snap the new one in.

It was useful that under the description of the part in the catalog, it showed that this part was often used to repair this issue. The service was great and the delivery was fast.

Pull refrigerator out from wall to shut off water and power. Remove ice bin, pulling front down then out. Remove screw at bottom of icemaker, then pull down to release two clips, Pull out a couple inches to get hand behind icemaker to release wiring harness connector. (squeeze top and bottom to release clips). Remove unit. Remove wiring harness and wire bail from old unit and install on new unit. Reverse steps to install new unit. Make sure ice bin is fully inserted, or unit will not function.

Wow! less Than 15 mins to install, called partSelect and within two days the Auger arrived and with handy socket it was done!

After checking the water valves ordered new ice maker. received the part three days after ordering! Clearing out food, removing the old one and installing the new unit took under 15 minutes. Everything went fine.

Once the part arrived, which was very quickly BTW..all I had to do was remove the old filter and then just screw the new one into place....Now I just happen to be both female and blonde but was able to get the job done in less than 15 minutes (that includes opening the box) and with very little water dripping from the old filter!!! Looks like I could work as the Maytag repair woman soon!!