GT2128PEFW Amana Refrigerator - Instructions

I first looked at the current assembly so that I could see how the new parts were to go (thanks Dad!) Then I removed the drawer and unscrewed the rails. Next, I removed the guide wheels from the old set of rails and installed them into the new rails. After that it was just a matter of screwing in the new rails and sliding the old drawer front plate onto the new drawer. Whala! Back in business.

I did not do the repair yet, there is no schematic on how to route the hose; also no description of how to do the routing/connections.

I first removed the drawer and then removed the shelf to which the drawer guide is mounted. Removing the drawer guide from the shelf was the hardest part - it was quite tight. I used a piece of wood and a light tap from a hammer to get it free. I had to reuse the roller from the old drawer glide (one screw). I snapped the new glide onto the shelf and I was in business. The best part was that the part arrived the day after ordering it - though I didn't request overnight delivery and the repair took less than 10 minutes.

I removed the tabs and/or their pieces that had broken off the shelf from the slots where they hung.
Replaced shelf with the new one I purchased on line and tapped it into place using a folded dish towel placed on top of the shelf and gently tapping it into place.
What did we do before the internet and part select.com? Thanks for your services.

Pried out old part with screwdriver. Unplugged. When new part came, just plugged it in and pushed the part into place.

I removed the ice catcher from the excellent packaging, rinsed it, and placed it on the counter next to the fridge. I opened the door the the freezer and placed the ice catcher under the icemaker. I lowered the arm on the icemaker and closed the door to the freezer. Then I opened the door to fridge, took out a Guinness, popped the top, and sat down to savor my success.

Disconncted power, pulled plug on disconnect, loosened 3 ice maker attach screws, removed ice maker. carefully removed old broken part, to understand reasembly. Reinstalled new water fill & bearing part.. hung icemaker and tightened attach screws. Reattached electrical plug.. turned on power, it all worked. .took about 45 min to remove, 15 min to reinstall. Right tools needed re disassembly AND ASSEMBLY

The plastic fill cup part is also used to hold one end of the wire “one/off” switch that is manually activated or activated when the ice tray is full. This wire piece fell out because one end, that is part of the plastic fill cup, broke off. The wire switch was fine.

The video demos show you exactly what to do. The repair man showed me a trick to speed up the testing process. The trick is to insert a wire jumper cable to actuate the ice maker and make it rotate. But this isn’t necessary.

Hardest part of this fix is emptying the freezer (bottom with a slide out door) and removing the door.

Why this part is so expensive is beyond me. But I’m happy it was available for a 24yo fridge that still works!!

Removed damaged piece and installed new one. Took less than 5 minutes.

I just popped out the old switch with a flat head screwdriver. Removed the connections and then installed new switch by reversing steps. Popped in back in and the light went on.

Replaced with new rail & popped it into place

It was this simple: Open the box. Proceed to the refrigerator and open the door. Align the brackets with the slots and push. Fill the shelf with your stuff. Close the refrigerator and say, "Thank you Partselect!"

Removed old ejector arm and installed new part.

I removed the old one and replaced with the new one. The right side one was quite easy whereas the left one took a longer time.

tricky part was removal of the old drawer rails. they have a little nub that sides in but does not slide out (the nub is a small triangle piece) so easily. needed to revmove the nub by use of a chisel (sharp knife would work). once that nub was gone the old rail slipped out and the new one slid right in.