GT2128PEFW Amana Refrigerator - Instructions

Once I identified the bit that would remove the screw, the rest of the repair took 5 minutes. I removed the screw and discarded the remains of the original but now broken shelf support. With the same screw I simply attached the new shelf support that I received from PartSelect.com. End of story.

When the new glide rail didn't look any different that the one I thought was broken, I thought I'd assessed the wrong broken part as everytime I tried to put it in the slots it would still fall off, just like the old one.. But I went back and reread the other repair stories to get a picture in my mind what they were talking about. I realized I needed to get the glass shelf off but it wouldn't budge. I found the original information booklet and realized the two blue clips in the shelf tracks were nothing more than packing clips (we've had the fridge 8 year.) when I got those off (these took the most time and a flat head screwdriver) the shelf came right off. Then I put the glide rail brackets in the appropriate slots, pushed the rail toward the front of the shelf and when it got to the place of resistance, I just applied steady, gentle pressure to get the brackets to lock in place in the slots. Repair done, placed shelf back in fridge, put drawer back on, and it was done. Oh, forgot, I first had to take the little wheel thingy off the old raid and screw it onto the new rail before attaching the new rail to the shelf. By the Way, this was really easy to do. I'm a 66 year old grandmother and this was my first refrigerator repair. Always read the previous repair stories--they really do tell you what you need to do.

inserted a knife between the switch and the plastic interior in order to pop the switch out.
then took off the 2 wires on the old switch put them on the new switch and reinserted the switch into the plastic interior.

I took a chance and ordered a switch that is next to the top of the door. looked for how to remove it easily done in ten minutes works fine last long time.

I took the freezer door off. Gasket screws ran on the four side of the door. I unscrewed the top and three sides but the bottom screws were completely rusted and stuck. As the refrigerator was almost 19 years old which is the predicted lifespan I decided to just buy a new refrigerator. I was able to adjust the old gasket and got the freezer working normally but decided to go ahead with the replacement.

I googled 'appliance repair' and discovered PartSelect. Tracking down the right part was easy - all I needed was a measuring tape to compare with the gridline
Ordering was easy and installing it was a breeze.
It was nice to know I don't have to depend on an appliance repair man or local store to fix everything.

The light rocker switch wasnt working. I found the part on the web site. It was so easy. I used a screw driver to pop out the old one and pop the new one in. It took 5 min. Thanks!!!

Very simple fix, remove 3 screws, two connectors to the old switch

I removed the switch housing (4 screws), replacing the switch in the housing was a snap. It took 5 minutes, cost $8 and light works like new!

Why didn't I order this part and do the repair earlier? Very simple.

Snapped it together and slid it in...

Popped rail off and replaced with new one. Video showed how to do it. A bit tight to remove and just needed a little strength and patience.

I unscrewed the support and replaced it with one that I ordered. It was fast and easy.

I first looked at the current assembly so that I could see how the new parts were to go (thanks Dad!) Then I removed the drawer and unscrewed the rails. Next, I removed the guide wheels from the old set of rails and installed them into the new rails. After that it was just a matter of screwing in the new rails and sliding the old drawer front plate onto the new drawer. Whala! Back in business.

Removed screws & old seal replaced seal and screws.

Result: New seal will not lay flat against the door making it difficult to close the door completely and causing the compressor to work overtime. I am hoping that it eventually flattens out.

I merely removed the old one and replaced the old one, I luckily had a ratcheting screw driver which made things go alot quicker as there were 36 screws holding the gasket on the inside of the door, also I had to replace some of the screws that I tightened as they stripped out in the door metal, I GOT SOME OF THE SAME DIMENTION with a slightly larger thread new screws and carefully screwed them in with no problems at all. Thank you for your professional speedy service. I will surely contact you again when I need parts for my appliances even if I m not the MAYTAG repair man.