GT2488PKCW Amana Refrigerator - Instructions

Pried out ice blade bar and removed broken water fill cup and replaced with new one.The whole repair costs $9.52 So I saved $ 190 over the cost of Appliance man visit!
It would have been $150& $50 for visit to replace ice maker unit.

A very cold and brittle switch in a 17 year old fridge. Used screwdrivers to pry out with some resistance Had to cut the molded plug in half and split wires, because replacement contacts were farther apart than the original. End result, works great.

took off lower bracket, replaced parts, put back together, no more squeek!

I took the original shelf out of the fridge with the brackets and the slide rail attached. The most difficult part was actually dismounting the slide rail from the bracket so I could replace it. I did this by leveraging the rail away from the bracket with a screwdriver so it could move freely and then banged it out. Once the old slide rail was off I just snapped in the new piece, screwed the wheel from the old rail onto the new one.

Removed screw holding the broken support then using the same screw installed new support. Easy job.

Removed the Crisper drawers and shelf. I then used a nutdriver to remove the broken supports, and installed the new supports using the same screws.

Popped the old one out with a kitchen knife and popped the new one back in. It tool less than 15 seconds!!

My owners manual said to unplug fridge from elec outlet, use a kitchen knife to gently pry off the switch plate
(manual had a pictoral example), unclip the two wire, replace with on new switch and replace the switch. Close
door and plug back in. Open door to check that the lite
works. Walla! It did. Thanks!

Sincerely, Ron Marshall, Billings, MT

I pried the old one out with a screw driver and pushed the new one in. I expected instructions in the box it came in but there were none.

Please bear in mind I am 65 years old & it was harder to get up & down off the floor then to change the switch. Was very easy - watched video, unplugged unit. I used the putty knife at the right front corner to work loose, when it came loose had to loose the left side a little. The unit pulled out easily. detached the wired that had a single plug with 2 prongs on it. Attached the plug, pushed new switch into place. There was no way you could place wires on wrong prong. When done, plugged refrigerator back in & checked if working. I CAN SEE THE LIGHT and the food in the freezer now. Thank you for making an easy repair.

Had to remove the ice-maker (also easier than trying to work inside the freezer letting all the cold air out). A few mounting screws and an electrical connection in the back. After it was out you will need to remove the cover (not the superficial cover that just pries off) where the gear is behind it, just far enough so you can get the mounting tabs on the ice-stripper in. In order to to move this cover out, after removing the screws (the obvious), you'll need needle nose pliers to ever so slightly squeeze the plastic clips together that hold the plastic movable bracket and the metal ice level arm/switch, so it will pop out. Once you have room to put the ice stripper in, it should just all snap back together, then proceed in reverse to put it all back together.

I did not remove te freezer door but did take off the fridge door. Removed all the screws- (way too many ),removed the old gasket and replaced. The job did not take long to do but was very tedious.

After receiving the new part almost immediately,using two screw drivers, removed the broken switch from the plastic frame. Be careful not to scratch or otherwise tear the plastic...very pliable. Since the original switch was factory installed and the wires were packed in fiberglass insulation, the switch came out but the wires and clips were still in place and could not reach the new switch. It was necessary to pull them down with bent long nose pliers...used a lot of "pull" but the wires held up.Connected the switch, turned the power on and there was light! Reports from other users really took the uncertainty out of the task.

Took ice maker out all together we removed 4 to 5 screws had to remove axel to get the broken piece out and new one in my husband said it was easy in and out in about 15 minutes saved about 150. 00 Thanks partslect

Removing the side rail was a bit difficult. You had to depress the locking tab with the putty knife and push the rail back to get it off. It took 2 of us working together to get it to work. Once we got that off, putting the new one on and installing the meat drawer was very easy.