GT2488PKCW Amana Refrigerator - Instructions
Jump to:
Keep searches simple. Use keywords, e.g. "leaking", "pump", "broken" or "fit".
- Customer:
- lloyd from california, KY
- Parts Used:
- 67764-1
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
broken crisper drawer mount
removed old mount with allen wrench replaced with new mount
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Paula from Rush, NY
- Parts Used:
- W11384469
- Difficulty Level:
- Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Pliers, Screw drivers
light switch sticking
I watched the video and thought "I can do this". Made some notes and then proceeded to remove the old switch and replace with the new one. Thank you.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Louis from Beloit, WI
- Parts Used:
- W11384469
- Difficulty Level:
- A Bit Difficult
- Total Repair Time:
- Less than 15 mins
Light did not come on (bad bulb!) on TC18KL
I have never before seen a bulb with the filament intact not light. If the bulb's filament seems intact, screw the bulb into a known working lamp and see if it lights. When screwing it back into the socket in the fridge, it takes a bit of extra effort to fully seat (until it does, it won't light!). For replacing the switch, I unplugged the unit, used a paint scraper and worked it under the switch bezel from the right side. A bit of moxie, and the switch came out. The replacement switch had a different spade contact spacing than the original. I used a pair of scissors to cut the rubber bridge between the two switch wire connectors so I could connect to the new switch. In the end, it turned out to be the bulb. NOTE: The Model TC18KL is _not_ listed! What I finally found that the number "P7803211WL" on the sticker is actually a manufacturing code. Found this out by searching, and Sears' part search came up with matches.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Dean from Lewis Center, OH
- Parts Used:
- WP61002653, WP61002308, WP61002307
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Screw drivers
plastic rail broke
snapped old rail off put new one on. actually. i supervised my wife did the fix. she got tired of me putting it off.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Joseph T. from Morgantown, WV
- Parts Used:
- W11384469
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
Light switch went bad
Simply stick a putty knife between the switch and refrig wall. Pop out old swith, remove both wires by pulling off switch by terminals. Throw switch out. Put wires on new switch and push into slot and all done. Nothing to it! Took me 5 minutes if th
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Anthony from Broadlands, VA
- Parts Used:
- 67764-1
- Difficulty Level:
- Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Screw drivers
Broken crisper support
The main issue is that my supports are NOT held on by screws -- they are behind the fridge wall and can not be removed. So this is my solution (ignore the 'fix kit' -- it is useless and is just this part plus a metal screw. It cost me $20 to find this out). Here is what I did: 1) Cut off the old support with a knife. 2) Get a small toggle bolt (I used 1/8" x 2", < $2 from Home Depot) and thread into new support. 3) Dig around in insulation to make sure there is space for toggle to flip open. 4) Install!!!! Wish I'd thought of this before :-)
Was this instruction helpful to you?
Thank you for voting!