AC2228HEKB Amana Refrigerator - Instructions
Jump to:
Keep searches simple. Use keywords, e.g. "leaking", "pump", "broken" or "fit".
- Customer:
- James from New Lenox, IL
- Parts Used:
- WP67005959
- Difficulty Level:
- Easy
- Total Repair Time:
- 15 - 30 mins
- Tools:
- Nutdriver
Ice tray track was broken- hanging down with weight
Took ice tray out, removed plastic decorative cover, remove the four nuts under the cover, slide out the ice auger assembly as one piece. do not take auger assembly apart. I repaired mine once, difficult without a schematic picture, many parts, replaced everything back into the new ice bucket. Easy job!
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Ralph from St Petersburg, FL
- Parts Used:
- WP67007098, WP67004119, WP12665101, WP12565502, WP12562701
- Difficulty Level:
- Really Easy
- Total Repair Time:
- 15 - 30 mins
- Tools:
- Nutdriver, Screw drivers
Ice cube door not shutting
Took the front panel off,replaced the parts inside on the door ,Replaced the panel ,Tested
Now found out that it is the solniod that is bad ,Part on order ,Thanks
Now found out that it is the solniod that is bad ,Part on order ,Thanks
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Edward from Florance, MT
- Parts Used:
- WPD7749401
- Difficulty Level:
- Easy
- Total Repair Time:
- 15 - 30 mins
- Tools:
- Nutdriver
Auger in the ice tray not turning
Removed ice container, replaced end cap that holds Auger shaft that connects to shaft that turns the Auger. End cap plastic nubs wear where it makes contact to the turning stub. Removing a few screws on the front of ice container allows the Auger shaft to slide forward and away from the end cap. Maneuver end cap from shaft, replace using same maneuver and that is it.
Pretty easy, even for a novice like me. A $6.00 end cap verses the whole assembly at around $70.00
I'm pleased.......
Pretty easy, even for a novice like me. A $6.00 end cap verses the whole assembly at around $70.00
I'm pleased.......
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Aliki from Miami, FL
- Parts Used:
- WP628356
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
Fill cup broke.
Very easy to order from parts select. Took seconds to replace.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Doug from PLEASANT VIEW, TN
- Parts Used:
- W11396033
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
Light switch in freezer side got broken
Took a putty knife and
Removed the old switch removed the spade terminals from the old switch and replaced them on the new switch and just pushed the new switch back in place
Removed the old switch removed the spade terminals from the old switch and replaced them on the new switch and just pushed the new switch back in place
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- paula from julian, CA
- Parts Used:
- R0181181
- Difficulty Level:
- Easy
- Total Repair Time:
- 15 - 30 mins
- Tools:
- Nutdriver, Screw drivers
door would not self close tightly
Remove two screws from top door hinge.
Remove door from unit
Remove old broken plastic cam 1 screw
Replace new door cam tighten 1 screw
Reinstall door and top hinge screws.
Remove door from unit
Remove old broken plastic cam 1 screw
Replace new door cam tighten 1 screw
Reinstall door and top hinge screws.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Mason from Tallahassee, FL
- Parts Used:
- R0181181
- Difficulty Level:
- Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Screw drivers
Cam snapped in half on bottom of door
Super easy - emptied door of all food, unscrewed bracket from top of door, lifted door off and set aside. Broken cam removed, new one screwed in, and lubed with some Vaseline. Set door back in new cam, screwed bracket into the top, and good to go. I was kinda worried about shopping from PartSelect since I had never heard about them, but the part was here in less than 2 days. Pretty awesome little company.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- George from Tunnel Hill, GA
- Parts Used:
- WP12562701
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
Ice forming around ice chute
I had to order three times before I got the right part. This was due to my rush to fix the problem and not studing the diagram carefully (black and white diagrams are not that clear). The repair was very simple. Just remove the rubber from the plastic door and slip on the new one.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- John from Capac, MI
- Parts Used:
- M1205302, WP10450603
- Difficulty Level:
- Really Easy
- Total Repair Time:
- 15 - 30 mins
- Tools:
- Nutdriver
broken roller
proped up frig, loosened screws, cut pin, installed rooler w/ new pin, rounded pin end, reistalled, lowered frig...everyone happy, thanks again partselect.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Marshall from Marrero, LA
- Parts Used:
- WP12740302
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Socket set
Ice Maker Auger
Wow! less Than 15 mins to install, called partSelect and within two days the Auger arrived and with handy socket it was done!
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Dennis from Salcha, AK
- Parts Used:
- 67005817
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Pliers
Meat drawer was broken
Removed old drawer. Then took old plastic rollers install in new drawer and put unit back together.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Sarkis from Havertown, PA
- Parts Used:
- R0181181
- Difficulty Level:
- Really Easy
- Total Repair Time:
- 15 - 30 mins
- Tools:
- Nutdriver
Door would not close properly
Removed the door by taking 3 screws out of the top and lifting straight up, then replaced with the new parts and very easily replaced the door, worked ike a charm, if i didn't know any better it was like factory new
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Dennis from Kerrville, TX
- Parts Used:
- R0181181
- Difficulty Level:
- Really Easy
- Total Repair Time:
- 30 - 60 mins
- Tools:
- Nutdriver, Screw drivers
The door made a loud noise on opening and closing.
Emptied the door.
Removed the door, top bolts first.
Lifted out the door.
Installed new cam at the bottom.
Set the door back in place.
Bolted the top hinge back on.
Smooth!
The part came quickly and was the right one. You can't imagine how many outfits lose it here. Well done and thanks.
Removed the door, top bolts first.
Lifted out the door.
Installed new cam at the bottom.
Set the door back in place.
Bolted the top hinge back on.
Smooth!
The part came quickly and was the right one. You can't imagine how many outfits lose it here. Well done and thanks.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- laurie from gold canyon, AZ
- Parts Used:
- EDR4RXD1
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
This is almost embarassing but you asked....
Once the part arrived, which was very quickly BTW..all I had to do was remove the old filter and then just screw the new one into place....Now I just happen to be both female and blonde but was able to get the job done in less than 15 minutes (that includes opening the box) and with very little water dripping from the old filter!!! Looks like I could work as the Maytag repair woman soon!!
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Jon from Butler, PA
- Parts Used:
- R0181181
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Nutdriver, Screw drivers, Socket set
Bottom Cam broke on Fridge Door
Removed top hinge cover and socketed out hinge nuts. Lifted door off bottom hinge. Socketed out broken bottom cam and replaced with new. Reset door with someone lifting and the other guiding. Reattached top hinge and cover. Voila.
Was this instruction helpful to you?
Thank you for voting!