GC2227EEDW Admiral Refrigerator - Instructions
Jump to:
Keep searches simple. Use keywords, e.g. "leaking", "pump", "broken" or "fit".
- Customer:
- THOMAS from WILLARD, OH
- Parts Used:
- W11384469
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
defective light switch
inserted a knife between the switch and the plastic interior in order to pop the switch out.
then took off the 2 wires on the old switch put them on the new switch and reinserted the switch into the plastic interior.
then took off the 2 wires on the old switch put them on the new switch and reinserted the switch into the plastic interior.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Judy from HIGBEE, MO
- Parts Used:
- WP61002623
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
I broke the crisper glass shelf while cleaning my refrigerator.
This replacement glass shelf arrived the very next day-after it was shipped. I was so impressed with the easy method of ordering and the prompt delivery of this product-also, the quality of the shelf was perfect. Great service!! I would recommend this for everything-as far as parts needed for repair or replacement.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- stu from richmond, VA
- Parts Used:
- W11384469
- Difficulty Level:
- Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Socket set
fridge door switch did not work
I removed the switch housing (4 screws), replacing the switch in the housing was a snap. It took 5 minutes, cost $8 and light works like new!
Why didn't I order this part and do the repair earlier? Very simple.
Why didn't I order this part and do the repair earlier? Very simple.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Bill from Hebron, NH
- Parts Used:
- 61004441
- Difficulty Level:
- A Bit Difficult
- Total Repair Time:
- Less than 15 mins
- Tools:
- Screw drivers
Our ice and water dispenser was "running on" and spewing onto the floor each time it was used.
We removed the old part, which actually looked quite functional. We put on the new part, thinking that the repair was not going to be effective, and that we were going to need other parts. But, the refrigerator is working perfectly now, and I have no more run-ons onto the floor. THank you very much.
Was this instruction helpful to you?
Thank you for voting!
Ice Dispenser door broken
The repair went just as the short video showed. The paper instructions included with the part were not too good the photos were copies of copies from years ago with all the detail gone. But with the video on your website it was a snap for anyone with some mechanical skills.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Craig from Fenton, MO
- Parts Used:
- 12001991
- Difficulty Level:
- Easy
- Total Repair Time:
- 15 - 30 mins
- Tools:
- Nutdriver, Pliers, Screw drivers
Ice was jamming in delivery chute
The round sealing door of the ice chute had to be replaced a alignment tab broke off the side.
1) unplugged the appliance from its receptacle.
2) removed catch tray at bottom of ice water depenser exposing two screws.
3) removed screws and slid cover up and away from keyed studs.
4) unplugged ribben cable from front panel.
5) removed additional screws and lifted the chute door and solenoid assemble.
6) replaced components and reassembled in reverse order.
1) unplugged the appliance from its receptacle.
2) removed catch tray at bottom of ice water depenser exposing two screws.
3) removed screws and slid cover up and away from keyed studs.
4) unplugged ribben cable from front panel.
5) removed additional screws and lifted the chute door and solenoid assemble.
6) replaced components and reassembled in reverse order.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Alan from Scio, OH
- Parts Used:
- WP61005883
- Difficulty Level:
- Really Easy
- Total Repair Time:
- 15 - 30 mins
- Tools:
- Screw drivers
assembly door was broken and allowed warm air to freezer
First I removed the two screws to remove outside cover. Then removed three screws to the ice dispenser assembly. Slipped in the new round door assembly and replaced the removed screws. No problems.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Terrance from Great Falls, VA
- Parts Used:
- 12001991
- Difficulty Level:
- A Bit Difficult
- Total Repair Time:
- 1- 2 hours
- Tools:
- Screw drivers
Ice dispenser would not work
Our Refirgerator had custome wood covering to match the cabinets. Be sure to take the covering off first. There are four screws on the left edge fram that need to be removed and two on top of the tpe edge frame. The panels then slide right off. Remove the spill tray and unscew the two screws at the bottom. Slide up the key pad and there are three screws behind the key pad that have to come out. There are two "plug in connections that have to be disconnected to lift the dispenser unit out. Take care not to damage or separate the connector wire from the keypad and the circuitboard.
The new solenoid and flapper assembly is different than the original. My guess is the orginal design was part of the problem and the redesign allows the solenoid to work better. I was suprised the new assembly did not come with a tension spring... SO be careful and DO NOT loose the tension spring from the old assembly. there are two screws that hold the olde solenoid in plae wonce you remove the flapper and tension spring. Put the new solenoid in, hold the tapper out and put the flapper assembly in. Rotate the flapper rod until you can seat the solenoid tapper. Replace the tension Spring and then reassemble as in reverse order.
The new solenoid and flapper assembly is different than the original. My guess is the orginal design was part of the problem and the redesign allows the solenoid to work better. I was suprised the new assembly did not come with a tension spring... SO be careful and DO NOT loose the tension spring from the old assembly. there are two screws that hold the olde solenoid in plae wonce you remove the flapper and tension spring. Put the new solenoid in, hold the tapper out and put the flapper assembly in. Rotate the flapper rod until you can seat the solenoid tapper. Replace the tension Spring and then reassemble as in reverse order.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- June from Apple Valley, CA
- Parts Used:
- 61003754
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
Right hand bracket broke off in freezer section
At first I thought I had ordered the wrong bracket but all I had to do was push it up and pull down and it snapped right in place. If a 71 year old lady can do this any body can do it. Thank you for the fast service.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Thomas from Roseville, CA
- Parts Used:
- W11384469
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Screw drivers
Door light switch disintegrated
Very simple fix, remove 3 screws, two connectors to the old switch
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- dorotea from staten island, NY
- Parts Used:
- W11384469
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Screw drivers
Light didnt go on
The light rocker switch wasnt working. I found the part on the web site. It was so easy. I used a screw driver to pop out the old one and pop the new one in. It took 5 min. Thanks!!!
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- alfonso from palmetto bay, FL
- Parts Used:
- 12001991
- Difficulty Level:
- Really Easy
- Total Repair Time:
- 15 - 30 mins
Ice was forming at the door because leaking warm air.
I just follow the easy instructions on the video provided for the part in question. Easy to change and everything is working fine
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Orlando from Bayonne, NJ
- Parts Used:
- WP2300868
- Difficulty Level:
- Very Easy
- Total Repair Time:
- Less than 15 mins
Old one leaks on one side
Simply cut the water tube on both sides of connector and push in the new one.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Samuel from ALEXANDRIA, VA
- Parts Used:
- WPB5705307
- Difficulty Level:
- Difficult
- Total Repair Time:
- More than 2 hours
Ice from icemaker taste metallic; new ice maker directly from box
I did not do the repair yet, there is no schematic on how to route the hose; also no description of how to do the routing/connections.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- anthony from HAVELOCK, NC
- Parts Used:
- W11384469
- Difficulty Level:
- Really Easy
- Total Repair Time:
- 15 - 30 mins
changed the light bulb still would not work so I figured it was the switch sure enough.
I took a chance and ordered a switch that is next to the top of the door. looked for how to remove it easily done in ten minutes works fine last long time.
Was this instruction helpful to you?
Thank you for voting!