GC2227EEDW Admiral Refrigerator - Instructions

Discovered ice door tab was broken. Ice door out of position.
Disassembled door dispenser, pretty easy, two torx screws on bottom, two on upper part of unit. Slid unit up slightly, it sets over two studs on the top. Unplugged wire connector, set aside unit. Looked on internet for a replacement part. These folks had the easiest to use web site. Found the part, ordered the part, received it next day, but only ordered the least expensive delivery method, since we are both in Florida it worked out well.
I did not know when I ordered this part I would get it this quickly. Because cold air was pouring out of the hole left by the removal of the ice door, I put wide painters tape over the hole on the inside of the freezer door. This greatly reduced the flow of cold air.
After I received the part, I clipped it in place and reassembled the unit, it did not work. The solenoid that moves the door just hummed like it was jammed. I took it back apart and realized that I did not get the bracket that moves the ice door reattached properly. After I made sure the bracket was properly attached, i reassembled the unit and it worked great. It actually took longer to type this description than it did to do the job.
Good Luck, Mike

Removed the drip tray and cover panel. Then removed shoot housing, replaced broken door and reassembled in reverse order. Easy as pie.

removed outside water spill tray and removed exterior cover & interior cover exposing the door arm and solenoid. replaced with new parts including spring. Elontronics have a plug which is easy to disconnecct. & reconnect
old solenoid head would not have fit new door arm
and vice versa.
I strongly suggest using the kit.
A Torx type screw driver is required for all screws
on the Jenn-Air

I ordered the ice dispenser and selenoid door kit, it was easy to repair because I only needed the door. As per the instructions I removed about seven screws and disconnected the power source to the dispenser unit, pulled the unit out
and replaced the door in the two slots. Plugged the power source back into the slot, put the screws back in, now it works like new.
Thank you PartSelect, I received the part in just a couple of days. I recommend your service to everyone. I saved myself a lot of money and will order again on any needed
parts in the future.

I simply removed the old switch using 2 small screwdrivers and the old switch case popped out. I then upluged the wires from the old switch and reversed the process. Didn't take longer than 5 minutes begining to end! Thank you for the great service! Duncan quaid

The actuator rubber pad had hardened over time so that it wouldn't allow the solenoid to retract and stop the flow. To fix: Turn off fuse to fridge. Removed the screws on fountain faceplate. Remove faceplate. Unscrew fountain computer assembly (2 or 3 screws) to access the actuator pad from behind. Unplugged the computer ribbon. Replace black actuator pad.

It works fine now.

This is an easy repair. It took me longer to remove the bins off the inside of the door and clean then up, then the actual repair. Remove the top hinge trim 1 Phillips screw. After the hinge trim is removed you'll see 3 hex screws. Remove the 3 screws. Hold and open the door half way, and lift up on the door. The door is not heavy. Use your kitchen table as a work bench. Place the door flat on the kitchen table . On the bottom of the door you'll see the "CLOSER" One screw removes it. Reverse operations and reassemble. Note: Put a little Vaseline grease on the pivot point. Thats it ... 15 minutes and your done plus you saved a $65.00 service call.

opened door, put in shelf then closed door

First I compared the old parts and new parts to see if I had ordered the right thing then I inserted the new stop into the door. Since the stop has a lip that needs to fit into the slot I the door, I used a hammer to push the part up so it would lock into the hole. Very Simple

At first I went to a local part supplier and they didn't have it in stock but could order it for me for $55.00 plus $10.00 to ship it. I told them I would have to think about it. I went home and got on the computer and found your web site and was I shocked when I saw the same part listed for $6.98 and $7.00 to ship it. You guys saved me $50.00. The part arrived in two day and took 5 min. to install. I now have light in my refrigerator. Thank you.

Popped out with butter knife and unplugged 3 prong connector and reversed with anew switch.

But, unfortunately it got broken again exactly same way as before.
So, I ordered same switch again for 2nd time.

Maytag should recall that Rocker Switch and build with better materials.

First I popped off the outer handle and removed the broken section. It was held on by two screws. I removed them and inserted the new piece fasten down with two screws and snaped the outer handle back in place.

Removed all 50 screws and replaced the seal. The door still comes open a tad but now it seals all the way. This was my first and last Maytag.

Removed the 2 screws holding the light bulb shield, then the 4 uolding the metal panel. Unplugged the olw door switch and replaced.
reassembled the pieces.

The Ice maker unit had to be removed and the shaft had to also be removed, which required dis-assembling the motor drive. The thickness of the shaft and the bearing fill cup prevents it from simply pushing it in place. Other than that I have Ice.