GGG390LXQ00 Whirlpool Range - Instructions

Put the back of stove on blocks of wood to get high enough to screw the new leg in.

I had to wait week for parts that were supposedly in stock No notice about delay I had to call to find out you really dropped the ball on this one

The steel mounting screw tends to seize in the aluminum burner head. It is not easy to extract, or to drill out and rethread. My advice is to replace the burner head at the same time.

Disassembly took the most time. After the gas was shut off all the burner heads were removed. Then all the control knobs. Then the front panel. Then the manifold mounting brackets. Then the range top. After all that, it was easy to unbolt the seized-up valve and install the replacement. After tightening down the new valve, be sure to leak-test! Re-installing the range top was tricky as it was difficult to align properly while getting all the burner bases in place. About 1 hour start-to-finish.

ordered new broiler pan

I determined the bake igniter was not working. If the bake ignitor does not work, the sensing unit to turn on the gas does not activate. I examined the bake igniter it was blacked significantly in one spot. There were no apperant cracks in it. I did a web search for the part and ordered it. Three days later it was delivered. Take pictures of each step if you fell the need. Pull stove away from wall turn off the gas, unplug power cord, remove panel in back of stove that covers the electrical, unplug the ignitor/element. Move to the front of the range and remove the oven rack. Remove the cover over burner tubes, it secured with several screws. Remove wing nuts for heat shield. Carefully remove burner tubes along with the attached ignitor/element. You will have to carefully guide the ignitor wires out with the burner tubes. Unscrew ignitor from the burner tube, attach new ignitor/element. Reverse the steps.

The knob was in English and a perfect fit !

unscrewed screws in the back of the stove. inside the stove, replaced the old bake igniter with the new one and connected the electrical wire in the back of the stove.

Just replaced insert pan - was able to identify it on the internet web site by inserting model number. Ordered part on line and got it within a week! Easy peasy!

Everything worked perfectly---thanks to the suggestion of your call center agent. She suggested that since the replacement door handles were no longer available, I should consider repainting them--it worked like a charm. Please tell her she was a life saver. We rent that house in Fl and my returning tenants had complained about the discoloring refer handles. Thank you

Removed stove from slot in wall. Bent rear left leg would not unscrew due to bent metal bracket. Used hacksaw to cut out leg, then straightened metal bracket with small hammer and was able to screw new leg in and adjust height by using level on stove before reinserting stove its slot. Recheck level after pushing back in place and adjust front legs if necessary. If not for bent metal receiving bracket, would have taken much less time. Still easy tho. R'cvd part in two days. Very quick.

1. Opened oven door and removed bottom covers plates to expose igniter and removed it. 2. Located hole in oven rear where the igniter connector and leads went through. 3. Pulled oven forward to allow access to rear bottom left cover plate where leads came through and removed plate to obtain access. 4. Installed replacement igniter in place of old iginter and ran its leads and connector through the oven hole. 5. Since the new igniter connector was unlike the old one, I had to replace the new igniter connector with the old one. Allowing sufficient lengths to properly make splices, I cut the igniter connectors off so that I could eventually match the mating connecter to the oven control circuit. I used a wire striper and pliers to make good splices. I covered the splices with plastic wire nuts normally used for insulating splices. I left the splices and the igniter connector outside the oven back for protection from the heat inside the oven. 6. After ensuring that oven insulation material was positioned to essentially cover the hole where the connector wires go through, I replaced the cover plate at rear of the oven and the cover plates inside the oven. 7. I checked oven for proper operation and found it now to be OK. Range was returned to normal position..problem corrected.

removed oven door, unscrewed 2 screws on front of plate covering burner at bottom of oven. Undid wing nuts on tent-like cover, unscrewed 2 screws at back of burner (igniter "hiding" under left back side). Pulled oven away from wall (yuch, where did that stuff come from?), unscrewed 2 screws of bottom plate, undid connector to old igniter, fished wires with connector from new igniter, plugged them in. Attached new igniter to bottom of burner, rescrewed. Put all screws and parts back in correct places. Cleaned oven door before putting it back on. Turned oven on........baked bread!! Hooray! Repair was easy-peasy!

Followed instructions I found online at the Maytag site.

The range in my classroom had the leveling legs broke off by the summer staff. I ordered two new leveling legs and the night custodian replaced them in about 45 minutes and them leveled the stove. Parts were just as stated and easy to order.