S8757W1 Roper Range - Instructions

acyually need better instruction and a video of how to install. I did not tilt the motor so it was on a parallel with the drum and initiall had a thumping cause by the wrong location of the motor. Corrected that and it works fine

replaced motor

Cut the two wires approx 1 inch behind old connector and removed one screws to remove old connector, stripped approx 3/4 inch off the wires and connected them to the new wires on the new connector with wire caps and shrink wraps which came with the new connector. Replaced the old screw with the new screw and the job was completed. Be sure and disconnect power before starting!!

It was a very easy fix. I followed the instructions that came with the kit and cut the original cable. Everything you need is in the kit; very few parts. Piece of cake and saved a lot of money an appliance repair person would have charged. This burner works better than the rest. I'm seriously considering replacing the other three blocks.

The four kits arrived, use of a pliers and shink wrap and side cutters...strip wires, twist wires connect wire ties, shrink wrap...little fire, plug the elements...done...four in about ten minutes...Instructions in each package...no problem...very easy...saved twice the money or more...Thanks for the parts...recommend this site purchase...parts arrived very timely...J. Iriwn

Removed the back access panel of the stove. Removed 2 screws holding the temp sensor, replaced temp sensor, Installed back panel. Done 19 minutes.

Read the Use & Care Guide! I spent several hours trying to repair a dryer that was not broken because I was unaware of the "lint signal". While replacing a burnt out heater element I apparently disturbed the flapper on the lint signal box and it stuck in the open position. My wife who does the laundry has always kept the lint filter clean so we had never heard the lint signal and I assumed that the high pitched sound I was hearing must have been from a faulty gasket, belt, roller, pully, or motor. Boy is my face red!

Watched the how to video on the parts select site. The job to replace the motor was easy although I had some issues with the blower fan wheel as it is made of plastic and was frozen to the motor, yes I turned it the correct way for the left hand threads. I ended up distroying the blower fan wheel and had to buy a new one. I had to remove the rear plate to get at the fan component, but thta was easy to do also. This site should add a "Sometimes bought together" comment for the motor replacement. After all was done I read some of the other comments and found some others had the same problem with the fan wheel. Once I had all the parts the dryer went back together fairly quickly. The job was easy to do and I would believe almost anyone could do it.

It is a washer/dryer combo. First I unplugged the unit. I had to remove the top and front of the dryer, remove the belt and remove the drum. I then removed the side panel that the motor was on. That was a little tricky getting at a couple of the screws. I then took the flywheel off which was somewhat difficult. It screws off in the opposite direction and was hard to get loose. I unplugged the motor, no wires to connect. There is a clip on the front and back of the motor holding it in place. Take them off and the motor comes right out. Replace the new motor and screw the flywheel back on. Install the clips, plug the motor in and put everything back as you took it apart.

Removed the floor of the oven. Removed the flame difuser covering the burner. Igniter was in plain sight. Turned on the oven and saw that the element in the igniter did not glow. Removed the igniter. Found a replacement on this site. Ordered the replacement part, which I received 3 or 4 days later. Installed the new igniter. Turned on the oven. Saw the igniter element turn bright red. Replaced the difuser and the oven floor. Turned on the oven and bake 2 loaves of sour dough bread.

That should have been an easy repair according to previous responders that replaced this part.

The first issue is the Phillips head screw that fastens the sensor to the back of the oven was frozen and I had to drill it out.

The second issue was I could not pull the connector through the hole where the sensor wires pass. I decided to cut the sensor wires and use wire connectors to attach the sensor as instructed in the sheet provided with the sensor.

NOTE: You MUST use third party "gray" colored wire connectors that you can purchase in a hardware store. - the connectors provided DO NOT have a metal insert and even after several attempts would not grab the wires.

Another caution is you should use a self-tapping sheet metal screw to fasten the sensor to the oven wall if you encounter the same frozen screw that I did!

After I installed the sensor I tested the oven but found that this DID NOT solve the problem! I needed to order the "hidden" bake element that is mounted under the bottom oven wall and also the broil/bake element that is mounted inside of the oven on the top. See my comments for the Bake Element (bottom)

I lifted the stove top and cut the two wire connected to the block. Attached the new wire connectors, new block and checked to make sure it was working. The part that took the longest was getting the screw out of the mounting brracked(it was corroded on). I sprayed some WD40 and waited 5 minuts, it came loose. Then i mounted the new bracket and installed the burner. double checked everything and lowered the top. Done

Followed instruction on web site

I had to take the top loose and raise it up. There are two screws in exhaust vent you have to take out then you can raise the top. When you raise the top you will have to take the front loose and open it up enough to take the drum out. Go to the back and take the lower cover off and take the screws holding the exhaust vent out so the vent will come out the top. When you take the vent out you will see a fan on the end of the motor shaft. The fan is threaded on the shaft and it is left handed threads. As you face the fan you will have to turn the fan to the right to get if off. You will need someone to hold a back up on the motor shaft inside the dryer to keep it from turning. Take the motor out then get the new motor and wire it according to instructions. Install the motor on the motor mount, put fan on then put everything back in reverse order that you took it apart. The hardest part for me was putting the clips on the motor when I put it back together. Hope this helps you.

Unplugged dryer. Removed lint tray screws. Opened top of dryer and removed the two face screws then removed front of dryer. Released the belt tensioner. Then removed the drum. Disconnected the wiring clip and with a creseant wrench held the back of motor and turned the nut in the front clockwise to loosen the motor from the vent fan. Then simply pulled the old motor out and reversed the steps and now have a great working old dryer again.