MGT8885XW02 Maytag Range - Instructions

My used stove had been dropped by the previous owner. While I could live with the minor scratches on one side the wooden shims holding up one corner were annoying. A new leveling leg was less than $2. I used a pair of needle nose pliers to straighten the mounting hole and screwed the new leg in. This used stove was originally $2000 but I bought it for $999. the new leg plus shipping was about $10. What a deal.

This is a no brainer. I am only doing this because you asked. Pull out the stove, tilt it back, remove broken leg, install new leg.

very simple fix. I removed the bake burner cover (the blue cover on the bottom of the oven), under that is the oven baffle which is held on with one wing nut and removed that. Then remove the oven bake igniter screws(two on the side), remove the orifice cover scew and remove then remove the oven bake burner gently. once these parts are off you need to remove the screws on the back of the oven ( I believe theres about 4 or 5 along each side and there are 4 on the bottom of the large metal plate. you only need to remove the large metal cover every thing else stays put. Disconnect the lower back burner attatchment which just clips into the connecter. once thats removed the part should come out easlily from the inside of the oven. Now take the new bake ignitor and feed the wires through the opening on the inside of the oven that allows the wires to come through to the back of the oven(you may need to feel around for the wires and move some of the insulation aside to feel them) once the wires come through the back connect the new part by clipping it to the harness the old part was removed from. At this point you should be able to reassemble the back of the oven exactly the way it was removed.Now go back to the inside of the oven, replace the bake burner gently over the bake burner orifice and put the orifice cover back on and reattach with it's screw. Position the bake igniter back into place on the side of the bake burner and replace the two screws previously removed. Once thats in place its time to put the oven baffle back on and secure with the wing nut and the last step is to place the bake burner cover. Just set the oven to bake and it should be working if thats in fact the problem..Good luck. Took me less than 15 minutes to fix.Some find it easier to remove the oven door but I didn't need to do this since I had enough room to access the front and the back of the oven without any trouble.

Followed instructions I found online at the Maytag site.

A fairly simple fix that this website did a nice job helping me diagnose and select the part. Only tricky part was the electrical connector on the range side had been cut so I had to splice the wires which wasn't a big problem. Just take your time to find the nuts and replace one part with another.

Removed two screws on sensor in the oven. Pulled out stove and after unplugging same removed the back panel. Sensor has an electric connection on the rear of the oven with a connection that is easily separated. Threaded new sensor electrical connection through inside of oven and connected on the back of stove. Pushed insulation back around the wire were in goes through to the oven. Replaced back on stove and screwed in two screws which hold sensor inside the oven. Replaced back cover on stove, plugged it in and pushed it back in place. Did the trick for me..

We have double wall ovens and each one only had a single oven rack in it. After 3+ years, I was tired of dealing with the issue so I ordered two new racks from PartSelect. They came quickly and fit perfectly. All I had to do was open the box, remove the rack and slide it into the oven. No muss, no fuss. Why didn't I do this years ago??

Similar to another customer, the racks were not removed before self-cleaning. The issue was that I AM THE HUSBAND and I admit that I did it. Ooops. Great price and if I do it again, I will go back to parts select to get a replacement.