MGR5750ADW Maytag Range - Instructions

This oven was located in a rental house I own.

I first removed the metal plate that covers the burners at the bottom of the oven. No tools required for this step.

Next I turned the oven to 300 degrees, waited 30 seconds and noticed that the igniter was glowing brightly, but the burners did not light.

I next turned the oven controls off, pulled the plug, and set to work removing the 2 screws holding a plate to the back oven wall and the 2 screws holding the igniter to the burner. These last 2 screws had corrosion on them and I needed to use vise-grips to get a firm hold on them. During reassembly these screws no longer held firmly because the hole they threaded into was enlarged during disassembly.

With the screws loose I pulled the igniter and fished the wires connected to it through the opening until I saw the connector. I then pulled the stove out of its opening and saw that there was a easily removable metal cover over the wires, and I took it off.

The new igniter came with an incompatible plug, so I cut off the connector on the stove wiring and on the new igniter and used wire nuts to make the new connections. I kept the orientation of the old and new plugs the same way in case the wiring mattered, but that was just being safe. I don't know if the igniter cares which of its wires go to which wire on the stove.

I reinstalled the screws holding the igniter, and shoved short sections of the supplied wiring into the screw holes so that the screws would hold more tightly. I shoved the supplied insulation into the opening that the wires passed through, and reattached the cover at the back of the stove.

I shoved the stove back into its opening, turned the oven on and it lit within 15 seconds.

I was very happy with the result, and the product I ordered arrived on time, well packaged and I'm a very happy customer.

Turned off water supply and unplugged appliance. Removed lower panel on back of refrigerator with 1/4 " nutdriver. Then removed supply line, and line to icemaker. removed valve from back panel and replaced with new valve. wrapped water connections with teflon tape, turned on supply line, checked for leaks, everything o.k..Replaced back panel and in 45 minutes had first drop of ice. Job requires moderate mechanical ability and minimum tools. Saved a PANT load of money by doing it myself. VERY satisfied with Partselect.com

First I removed two screws that hold the oven sensor in place. I then removed the screws that held the panel on the back of the oven. I simply unclipped the plastic adaptor and replaced the old sensor with the new one. I screwed the sensor back in and put the back panel on. turned the power back on to the oven and hit the bake button. Voila!! The oven turned on and now it works like new!!!

removed oven door, removed screws from bottom and sided, door is in layers, removed door layers like taking apart a sanwhich layer by layer, once i got to the inner layer i just had to bend out the little tab on the frame,remove the broken pane and place in the new one, bend the tab back and then put the door back together layer by layer, it was very easy and saved me money, and frustration in dealing with a repair man from a well known company who tried to tell me I needed to replace the whole door as the glass was factory sealed in the door, WELL! this girl's hair may be blonde but not that blonde, I received the glass the very next day, and it took me 40 minutes tops to replace the glass, EASY! KC

1st removed the door from the hinges by sliding it up. Then removed all the screws holding the door together. Then removed the screw securing the trim. Removed the screws from inside the trim holding the old handle... replaced the handle and trim. replaced all screws in reverse order. Replaced the door on the hinges. all done

i need to replace the lower oven igniter about 2-3 years
unplug the oven
open the oven door half way then slide the door up
take out both racks
push the bottom pan away from you and lift up
one screw holds the igniter on
pull the wire out until you get to the electrical plug
disconnect

I ordered the door glass from Part Select, which arrived quickly and in good condition. I loosened two sets of screws under the bottom glass holder frame, removed three screws at the top of the door to give more room. Slid the glass in place, re-installed and tightened the screws.The stove door looks great and works great. Great customer service too.

I am a retired lp Gas service person so this was quite
simple for me. Replaced the oven Igniter. What amazed me I placed my order and had the Igniter less than 24 hours. thank you so much for the quick service.

My oven stopped working and the display read F3 error. I looked up the code and found that it was probably the thermostat sensor. I ordered the part from partselect.com and when it arrived I went to install it but I ran into a somewhat scary issue. I found that I had to pull my oven out of the wall in order to replace the sensor.

After a minor nervous breakdown, I decided to go for it and found that it was much easier than I had imagined. Changing the sensor involves taking out the two screws that hold the sensor in place (inside of the oven), pulling it out to the point you can reach the connector, plugging in the new sensor and screwing it back in place. However, if you have an oven like my model, you have to pull out the whole oven from the wall in order to reach the plug on the sensor. This sounds like a lot of trouble but for me it was very easy. The oven is held in place with screws around the front side. Most are easily accessed and you don't have to take out any critical/complicated pieces of the oven. My screw gun made short issue of the problem and I found that the oven was out of the wall within minutes. I could then easily unscrew a small back cover, change the sensor and then screw the oven back into the wall. Being very careful, the whole operation took about 20 minutes. I recommend that you get help from a friend just because the oven is bulky. It is not heavy, an average sized male can handle the weight but it’s easier with a friend. Also, be careful that the gas hose which feeds the oven is long enough (and not tangled) for you to move the oven out of its space. Obviously, be careful about gas leaks.

Remove racks and pull out stove from wall. Remove back cover from stove. Unscrew and unplug sensor. Rethread new sensor wire through hole and plug in new sensor and rescrew plate that holds in place.

We had complications because of how the stove was installed, which delayed the "fix" time considerably.

Also installed ignitor. It was determined that both were bad. Gas would come on but not light. When oven would light, it would not re-light periodically to keep the temperature up, causing gas smell. This added time to repair of an additional 1 hour, and required removal of bottom drawer.

SHUT OFF GAS
disconnect FLEX LINE from gas PIPE
remove GAS pipe from rear of stove
remove rear panel
remove pre-shaped gas lines to burners and oven / broiler
separate dual control valve from pressure regulator
disconnect wiring from dual control valve
REASSEMBLE in OPPOSITE order
turn on gas
CHECK ALL FITTINGS FOR POSSIBLE LEAKS
Turn on each BURNER - making sure EACH one lites
turn on oven - making sure that the OVEN igniter lites the OVEN
set control on BROIL
turn on broiler - making sure that the BROILER
igniter lites the BROILER

Pulled the stove out from the wall. Removed the left side of the stove. Removed the wires from the old igniter. Modified four of the wire ends with the proper size spade connectors (supplied with the new part). Reinstalled the wires onto the new part. Tested the burners. Reinstalled the stove side. Moved the stove back into position.

Pulled off the oven door, just lift straight up. Pulled out the floor of the oven, very easy just lift from the back. The only problem I had was the screws holding the old igniter wouldn't come out, they just spun. I snipped them off and picked up two new ones at the hardware store. Pull the wiring harness in through the hole in the back of the oven. Unsnap old wiring harness, snap in new one. Reattach the new igniter, replace floor, replace door. Turn on oven and cook food... fairly easy repair.

first of all i have one advantage even though i am 70 yrs old i had a appliance shop for sears in the 60s and 70s and have not forgotten to much of the basics i am still in the security business and up on electronics. last time i had the company repair the oven , 70 dollars for the part 75 dollars for the svs call. (first igniter was on full warranty) well this time i decided to look for trhe part myself, i just went on line typed in oven repair parts and eventually all these sites came up. yours was the most professional looking and i took a chance. guess what everything you promised you delivered. price quality USA made parts and delivered in three days . opened package went to work less than fifteen minutes back in business.
will sure use you again if the need arises thank you

Pulled the oven away from wall to access rear of oven. Disconnect electric plug from duplex outlet, turn off gas supply ball valve. Removed two screws that retain sensor on inside of oven. Disconnected two prong sensor connector at rear of oven. Tied a length of string to sensor connector wires. Pulled old sensor out through front of oven. Use the string to tie onto new sensor connector wires and pull new sensor into place from rear of oven. Retain sensor with two screws. At back of oven, used connector jumper supplied with part package to make connection to existing connector.