MGR6775ADW Maytag Range - Instructions

the repair was not difficult ,take time cause back panel has to be removed to gain access to unplug the temp sensor ,it appear to work but the digital clock still flash not all the timebut it should not flash , not sure that i have fixed it

1. Opened oven door and removed bottom covers plates to expose igniter and removed it. 2. Located hole in oven rear where the igniter connector and leads went through. 3. Pulled oven forward to allow access to rear bottom left cover plate where leads came through and removed plate to obtain access. 4. Installed replacement igniter in place of old iginter and ran its leads and connector through the oven hole. 5. Since the new igniter connector was unlike the old one, I had to replace the new igniter connector with the old one. Allowing sufficient lengths to properly make splices, I cut the igniter connectors off so that I could eventually match the mating connecter to the oven control circuit. I used a wire striper and pliers to make good splices. I covered the splices with plastic wire nuts normally used for insulating splices. I left the splices and the igniter connector outside the oven back for protection from the heat inside the oven. 6. After ensuring that oven insulation material was positioned to essentially cover the hole where the connector wires go through, I replaced the cover plate at rear of the oven and the cover plates inside the oven. 7. I checked oven for proper operation and found it now to be OK. Range was returned to normal position..problem corrected.

I tried to take it out from the inside as the vidio shows. But it would not come out far enough. I pulled out the stove and removed back sheet metal panel. Unpluged the electric, Unhooked the temp sensor,pulled it out from the oven side. Put the new one through the hole,and rehooked it up. And got to clean up the dust and my missing oatmeal I spilled a while back. Turned it on. Checked it with a spare temp gage. Works so far.

The feedback from other customers was excellent. It does come apart in layers, and it helped me to number each layer with a sticky note as I dismantled it. I also kept the screws for each layer right next to the layer, so that I knew how many screws each layer used. The only thing I can add is that the tabs to remove the innermost glass from the frame are on one of the shorter sides of the rectangular frame. The tabs are part of the frame, and when you bend them outward the side of the frame detaches and you can replace the glass easily. In addition to the #1 Philips screwdriver, all I needed was a pair of pliers to bend the tabs.

Remove the big back panel (5 phillips screws). Confirm voltage is present when attempting to start the oven by unplugging the PROPER ignitor. I say proper because initially I thought that the broil ignitor was the culprit. Very upper ignitor is the broiler ignitor and the next one down is the ignitor for the upper oven. You will notice that the ignitor plugs differ between broiler and oven. New ignitor should have a male end. Once I confirmed that voltage was present when attempting to turn on the upper oven and probing the ignitor terminal plug, I proceeded to remove the lower cover inside the oven (2 screws very front side) and remove the burner assembly. (First you'll need to remove the oven door, easy, just tilt out part way and slide it up and off of the rails). The ignitor is mounted to the burner assembly. It's inevitable, the 5/16 hex screws (x2) will absolutely strip out so make sure you have some extras on hand. Replace the ignitor, reinstall and you should be good to go! I've read that you shouldn't touch the element with your fingers as this will compromise the life of the ignitor. Good luck!

This repair is only if your old igniters are working but they are so cracked that the spark is not going where it should be. TURN OF THE GAS SUPPLY VALVE BEHIND THE STOVE AND UNPLUG THE STOVE FROM THE WALL.I had to drill out most of the old screws to remove the burners plates because of all the old baked on spills. I bought replacement screws when I bought the igniters because I felt this would be a problem. My repair time included scrubbing the stove top. Once all the parts that make up the stovetop burners were removed (NOTE WHICH BURNER PLATE CAME FROM WHICH LOCATION, THEY ARE DIFFERENT SIZES) and I could see the pipes beneath the stove top, I cleared off the top and used a spreading knife to push in the clips on the left and right sides near the front of the stove. It was thin enough to fit in the space between the stove top and main body. Push the clip inward and pull up on the stove top and it will let you lift the top. Be careful because it may release suddenly so be gentle. I also removed the top section of the back of the stove to access the igniter terminal block. A few screws, nothing more. Be sure to take note of which wire goes where. (They are color coded). Unplug the old igniters. it is easiest to cut he old igniters off of the end of the wires and pull out three wires leaving only one. At the back left of the top of the stove there is a rectangle channel that the wires are running through. There is a clip that holds the wires loosely together. Remove the wires from that clip or the next part will be difficult. Run each of the new igniter wires through their respective holes in the stove top. BE CAREFUL NOT TO DAMAGE THE WIRE INSULATION IN ANY WAY. When you put the burner plates back on the igniters will be sandwiched in between the plate and the stove top. Using electrical tape, tape the connector ends of the new wires to the one remaining old wire. Gently pull the old wire through the rectangle channel, pulling from the back of the stove. Take your time so no damage occurs. Once the wires are pulled, plug them in to their respective terminals and place the wires in the loose clip. Make sure the new wires are not crossing the pipe openings where the burners are located. You can close the stove top and double check there are no wires across any of the burner openings. Re-assemble the burners and plug in the stove. DO NOT OPEN THE GAS VALVE. Turn on the stove and check to make sure the new igniters are working properly and sparking to the burner plate assemblies. You should see a controlled spark. Do not touch the burner plates or igniters or you will be shocked. If all are working then you may put the back cover on and open the gas valve. If none are working make sure the stove is plugged in. If some are working then check the connection on the terminal block and the wire insulation. If they are still not working then you've got bigger fish to fry. Good luck my friend. Happy fixing!

I removed the broken hinge and installed the new one, however the oven door didn't stay ajar but dropped open fast. So I took the old spring and installed it on the new hinge and it was improved. It just took a screwdriver.

Easy just loosened screws took apart door, removed broken glass and installed new glass.It took longer to clean the stove! Lol!

removing the screws holding the burner together was impossible. they snapped off and I had to drill them out. that took the most time. after that it was 100% easy hookup. clean up of the burner was done with a wire brush. good quality products. thanks.

Removed stove from slot in wall. Bent rear left leg would not unscrew due to bent metal bracket. Used hacksaw to cut out leg, then straightened metal bracket with small hammer and was able to screw new leg in and adjust height by using level on stove before reinserting stove its slot. Recheck level after pushing back in place and adjust front legs if necessary. If not for bent metal receiving bracket, would have taken much less time. Still easy tho. R'cvd part in two days. Very quick.

After we got the part in the mail my husband put it on and shortened the wires and put new plugs on the ends of the wires and we had to get a new plug put it on and it was fixed.

My first suggestion, after turning off the power to the unit, is to take the oven door off. Two simple screws and it's off! It makes getting to the temperature sensor much easier. I also moved the oven out so I could get access to the back to remove the rear panel. The ordered part came with two pigtails, neither of which fit my oven wiring harness. I cut one of them and the wiring from the faulty sensor, spliced them together with wire nuts and made my own connection harness. The new sensor went in with little effort. The wiring went together flawlessly with the spliced connection protected between the oven cavity and rear panel. Reattached the rear panel and the oven door, then slid the oven back into place. Turned on the electricity and back to normal! Problem resolved!!

Undid screws on front and some on the back and replaced part and put screws back on and it fixed the proble

I had to pull the range out from the wall and loosen the rear cover to free the connector for the sensor as it got stuck on a corner guide. Put the new sensor in, rear cover back on, range back in place and tested the oven. Oven heats fast now and keeps a more even temp. Makes me wonder how long I was trying to cook with a bad sensor.

Like other reviewers said it was pretty easy. Remember the order you take things off and keep the screws in groups so you remember which ones go back. I was a little surprised to see i had to take the bottom trim off door so that i could take out glass so i could reach brackets on top of door that hold on the handle, but this gave me a chance to do a good cleaning of the door. Not sure how grease gets inside the glass but there it was. Did this by myself but it would have been nice to have one more hand there to hold the glass as i put it all back together.