MGR6775ADW Maytag Range - Instructions

I pulled the oven door off and set it on the counter. I unscrewed all the visible screws and carefully removed the glass. Found some more screws that needed removal. Removed the old handle, attached the new. Then re-assembled everything. I kept parts aside in the order I took them off, so I knew what order to re-assemble. My only problem was the weight of the door as I am a 74 year old female and, to me, the door was very heavy. Otherwise it was not a difficult task.

Remove two screws back panel and remove sensor two screws inside top oven.

Once I saw the spring clips on the new door seal, it was easy to understadn how to remove the old seal and install the new one. Looks nice !

Removed the two screws pulled the element out and unhooked the wires then used one of the included adapters to reinstall the new sensor then screwed the two screws back in to secure the sensor. Everything works fine now.

I took out the old and replaced with the new. The hardest part was getting that tiny halogen bulb in that tiny little hole. It took longer to take the oven racks out and put them back in than to make the repairs.

unscrewed screws in the back of the stove. inside the stove, replaced the old bake igniter with the new one and connected the electrical wire in the back of the stove.

Just remove the old for new

Called a repairman who installed the piece of glass as the old piece was difficult to remove. Started project so I could clean the various glass pieces but was happy he came and finished the job. It took him over 30 minutes and like I said I had most of the door apart.

The lower oven would not heat up, the temperature stayed at 100. I'm pretty sure the same instructions apply for the upper oven. This is a pretty straightforward repair with a couple of minor bear traps. 1) Remove the oven door by simply lifting it up off the hinges. Not absolutely necessary, but helpful to get your head inside the oven. Not a bad idea to vacuum out the oven floor at this stage. 2) Remove the two Philips head screws at the front of the burner pan cover - the screws are at the very bottom inside the oven. 3) The pan cover lifts straight out of the oven, set it to the side. 4) Remove the burner cover held down by either one or two wing nuts - my oven only had one wing nut from the factory - nice job Maytag on your quality control!! 5) Loosen the screw holding down the burner cover in the far back right corner. This cover is a steel rectangular box that is a shield for the burner gas / air connection. Turn the box around to expose the burner end. 6) Remove the two screws that hold down the burner assembly. One screw is at the very front of the oven. The other screw is on the left side of the burner at the rear. Do NOT remove the pan held down by 6 or more screws. On my oven, the left rear screw was stripped. It stripped in a very weird way that took a long time to remove it. The threads inside the metal were fine, but the threads that had been exposed to heat were brittle and fell off. That meant the screw backed out about 3/4 of the way and then kept turning. This is where pliers come in handy. It will take some pulling up and turning with pliers to get those stripped screws out. I didn't want to cut off the screw because the cut out part would fall back into the lower pan. 7) Pull the oven out from the wall and unplug it from the electicity. Remove the 3 screws holding the left rear metal panel in place. There are two screws along the far left side and one down lower on the right. The panel is connected to the one next to it with tabs. 8) Unplug the ignitor. There is a white fireproof wire that comes up from the bottom of the oven that plugs into a white automotive style clip connector. Push the tab to release the clip and unplug the wire. 9) Wrap some stray wire or string around the plug to use as a pull wire when reassembling the oven. 10) Go back to the front of the oven and lift out the burner, be careful not wo pull your pull wire all the way out of the oven. Untie the pull wire. 11) Remove the two philips head screws that hold the ignitor to the burner bracket. 12) Reassemble! Attach the new ignitor with the two screws. 13) Push the wire into the lower part of the oven. 14) Go to the back of the oven and pull the wire through the oven wall. 15) Drop the burner in, making sure it mates up with the gas tube in the back right. 16) Flip the rectangular burner shield back and tighten it down. 16) Replace the two screws that hold down the burner tube, front and rear. 17) Replace the burner shield with the wing nut(s). 18) Replace the burner cover, or floor of the oven. 19) Go to the back of the oven, plug in the ignitor wire. 20) Replace the rear panel cover and secure it with the three screws. JOB FINISHED! Plug in the stove and push it back. The oven takes a few minutes to start heating, you should be able to see orange glow around the slots in the floor of the oven.

took off the back removed the burner top installed the switches and put it all back together Im a retired electrician not so sure the average guy could do this

removed the door, removed the bottom, removed the glass. The handle bracket it attached to the door but though the vented part. After removing the old handle just had to put it all together again, Not hare just a lot to take a apart.

The range in my classroom had the leveling legs broke off by the summer staff. I ordered two new leveling legs and the night custodian replaced them in about 45 minutes and them leveled the stove. Parts were just as stated and easy to order.

Removed grills, lower burner cover and burner inlet cover. I then pulled burner out far enough until plug for igniter was exposed. Unclipped wire connection by squeezing in retainer clip and then pulled apart. Pulled burner tube/igniter assembly out and removed two igniter retaining screws. Then reinstalled in reverse order.

I disconnected the electrical power, but not the gas line, and pulled the oven unit away from the wall. I unscrewed the old temperature sensor mount and only realized then the simple configuration: A wire from the sensor runs through the back of the internal oven space to the back of the oven unit through a thin space filled with insulation. The old sensor was easy to disconnect behind the oven unit and pull the old sensor and wire forward through the opening in the oven. The most challenging part was threading the new sensor wire from the oven interior through the back of the oven unit. The instructions and comments provided on-line by previous customers was EXTREMELY helpful. I wish I could do many more household repairs like this!

First I took the door off and outside to dump the glass in the trash which I had some Kevlar gloves so not to get cut. Removed the three screws on the bottom trim piece and the two on the sides remove the outside face glass next remove the four screws that hold the next glass. This glass is in a frame there is bent tab on one corner unbend open frame and install inner glass close frame rebend tab and reinstall all the parts.