MGR6772BDQ Maytag Range - Instructions

Simply remove two screws take old one off and line up and put new one on and replace the two screws. Couldn't have been easier.

Spoke to your very helpful staff, who advised me that a likely problem was the oven sensor. I took a chance and ordered the part, which came promptly. Your service video for the part was most helpful in my decision to try the part. Installation was a breeze, but it was the oven controller board that had failed and not the oven sensor. That called for a service professional, who ultimately fixed the problem. Your service though, was excellent and I would highly recommend you to others.

I switched the oven sensor easily enough, but it did not remedy the problem, so we are in the process of replacing the oven since it's about 20 yrs. old.

After reading from a Google search, why won't me maytag genius double oven light? I read that my oven will not open its gas valve until the igniter is hot, glowing red. Mine didn't glow red bad igniters. After ordering the new parts install was easy and under 15 mins. My advice is to be careful pulling the oven out to access the back panels, be careful not to scratch your flooring. 5 screws for the big panel, and 3 for the small panel. All Phillips head screws. 5 inside the oven to pull the old igniter. Easy job anyone can do it. I did both upper and lower ovens and the broiler igniters.

Hired a pro. Parts are difficult to get on a timely basis today , if at all. Screw up this repair by damaging the outer " black glass " and you buy a new stove. It took three weeks to get my replacement glass even though PS said the part was being sent within a day of the order. Even so , I am am happy to have gotten it , and will continue to use the company.

oven had to completely come out cause two sheet metal side panels had to be removed to get to hinge.

Removed the two screws holding the sensor to the rear oven wall. pulled out sensor wire. It was caught on other wires behind the oven. removed the three screws holding the 8" inspection plate in the center of the rear panel. Carefully move the insulation and reach in to grasp the back end of the sensor wire. Once free from the snag it easily pulls out with the sensor just as stated in the video. using the appropriate adaptor it was easy to re-asseble and and attach to the oven wall. Replace the rear panel with the three screws and it was done

Oven sensor replacement was easy. Thermistor was installed in less than 15 minutes. After installation STILL had "F3" error message. Harness was ok, "Clock" or ECU needed to be replaced. "Computer" is obsolete, no spares available, some companies will rebuilt for $400+. Since the stove was going to the landfill I had nothing to lose by taking the "Clock" apart. It has one chip that is probably the power supply and control chip, another chip is an EEPROM with 128 bytes of storage and the last is a darlington chip that controls the relays. Cleaned up everything that looked like it needed cleaning with alcohol. When I reassembled the unit the pins for the thermistor harness felt loose, so I took it apart, again, and found cold solder joints on all four pins. It must have been there all along but plugging and unplugging the harness finally broke out the solder so I could see it. Soldered the pins back in and now it all works. It's worth a try if you're getting the "F3" message. If the relays on your stove aren't working it would be a good idea to replace the darlington chip. Good luck.

UNPLUG THE POWER CORD! This particular model is a (slide-in) unit, it was wedged between to fixed cupboards/cabinets. Therefore, there are really no side panels to speak of, this made the repair slightly easier. I simply slid the unit out enough to unplug the power cord and access the right side of the unit. All one needs, at this point, is a Phillips head screw driver to remove a small metal panel installed just below the stove top panel (right side of range), its held with approx. 8 screws. There is one other panel that must be removed as well, (you may want to remove this panel first). It is an enameled-like panel approx. 5" wide x 36" long located at the front of the range (right side) running the length/height of the range (held with 2 screws). Get those 2 panels removed and you will see the spark module attached near center of range just under stove-top panel. Module is attached to a small metal bracket, module has 6 wires attached to it (2 feeding the module and 4 exiting the module to the burners). Bracket screws are nearly impossible to get at (you need a very stubby Phillips screw driver, if you can even get your hand in there). Anyway, I simply released the module from the bracket, then carefully bent the bracket back toward me; to provide work area for my hands. The bracket bends easily and really can't be broken. Now, at this point (using longer needle-nose pliers) detach the wires from the old module (remembering each wires location) or, as I did, hold the replacement module near the existing module and transfer the wires one at a time. Now, slap it all back together as you took it apart. Really simple job, total time is easily/generally under 30 minutes. It may be easier to access the module by removing all the burner components and raising the stove-top? Not sure? I chose not to do the repair that way. Hard part was locating where the manufacturer hid the module on the range. :- ) D.I.Y.ers Rock!!!

I took the broiler pan out of the shipping container and put it in the oven.

Turned off breakers to oven. Removed two screws that held oven in cabinet. Removed oven door by opening slightly and pulling up on door. Pulled oven out 1/3 of way. Took out four screws on top of control panel. Took oven light switch off by unscrewing holding ring. Removed temp knob on right by pulling. Removed start / stop knob same way.Removed glass straight out. Removed four screws that held elecrtonic clock conrtol board. Unpluged three wire plug from right side and the nine wire plug from the left side. Worked board out at and angle. Went backwards to connect and replace board, screws and door.Slid oven back in and tested oven after turning breakers back on, worked like new.

Took screws out of the back on the side the sensor was on, unplugged it & took out the two screws on the inside of the oven to release the sensor. Put new sensor in place with the two screws & used one of the adapters to plug in the new sensor. Put screws back in the back panel & turned on the oven which unfortunately is still 50 degrees low. Need a new clock with computer which is out of stock & unavailable. I was an electrician for 25 years so didn't experience any problems. It was a cheap thing to try.

Removed door, dissasembled door cleaned all broken glass, installed new glass, re-assembled door and put door back on oven.

Very simple project.

Got a bent metal coathook to temporarily release the oven door, removed the screws from the old probe, inserted the new one, and hooked it up, using the one of the plug adapters provided. Problem solved! The oven door latch was now disengaged, the oven would now accept temperature inputs, and the rear cooling fan (which wouldn't shut off) now turned off. That's a lot of things working better for less than $50!

I received my glass panel realy quick from Part Select. It was an eansy job to install the new pane.
It took less than an hour. Thanks for Your prompt service.